Next-Generation Firewall
Configure an Aggregate Ethernet Interface Variable
Table of Contents
Expand All
|
Collapse All
Next-Generation Firewall Docs
-
Cloud Management of NGFWs
- PAN-OS 11.1 & Later
- PAN-OS 11.0 (EoL)
- PAN-OS 10.2
- PAN-OS 10.1
- PAN-OS 10.0 (EoL)
- PAN-OS 9.1 (EoL)
- Cloud Management of NGFWs
-
-
-
- Configure a Filter Access List
- Configure a Filter Prefix List
- Configure a Filter Community List
- Configure a BGP Filter Route Map
- Configure a Filter Route Maps Redistribution List
- Configure a Filter AS Path Access List
- Configure an Address Family Profile
- Configure a BGP Authentication Profile
- Configure a BGP Redistribution Profile
- Configure a BGP Filtering Profile
- Configure an OSPF Authentication Profile
- Configure a Logical Router
- Configure a Static Route
- Configure OSPF
- Configure BGP
- Configure an IPSec Tunnel
- Web Proxy
- Cheat Sheet: GlobalProtect for Cloud Management of NGFWs
-
PAN-OS 11.1 & Later
- PAN-OS 11.1 & Later
- PAN-OS 11.0 (EoL)
- PAN-OS 10.2
- PAN-OS 10.1
-
- Tap Interfaces
-
- Layer 2 and Layer 3 Packets over a Virtual Wire
- Port Speeds of Virtual Wire Interfaces
- LLDP over a Virtual Wire
- Aggregated Interfaces for a Virtual Wire
- Virtual Wire Support of High Availability
- Zone Protection for a Virtual Wire Interface
- VLAN-Tagged Traffic
- Virtual Wire Subinterfaces
- Configure Virtual Wires
- Configure a PPPoE Client on a Subinterface
- Configure an IPv6 PPPoE Client
- Configure an Aggregate Interface Group
- Configure Bonjour Reflector for Network Segmentation
- Use Interface Management Profiles to Restrict Access
-
- DHCP Overview
- Firewall as a DHCP Server and Client
- Firewall as a DHCPv6 Client
- DHCP Messages
- Dynamic IPv6 Addressing on the Management Interface
- Configure an Interface as a DHCP Server
- Configure an Interface as a DHCPv4 Client
- Configure an Interface as a DHCPv6 Client with Prefix Delegation
- Configure the Management Interface as a DHCP Client
- Configure the Management Interface for Dynamic IPv6 Address Assignment
- Configure an Interface as a DHCP Relay Agent
-
- DNS Overview
- DNS Proxy Object
- DNS Server Profile
- Multi-Tenant DNS Deployments
- Configure a DNS Proxy Object
- Configure a DNS Server Profile
- Use Case 1: Firewall Requires DNS Resolution
- Use Case 2: ISP Tenant Uses DNS Proxy to Handle DNS Resolution for Security Policies, Reporting, and Services within its Virtual System
- Use Case 3: Firewall Acts as DNS Proxy Between Client and Server
- DNS Proxy Rule and FQDN Matching
-
- NAT Rule Capacities
- Dynamic IP and Port NAT Oversubscription
- Dataplane NAT Memory Statistics
-
- Translate Internal Client IP Addresses to Your Public IP Address (Source DIPP NAT)
- Create a Source NAT Rule with Persistent DIPP
- PAN-OS
- Strata Cloud Manager
- Enable Clients on the Internal Network to Access your Public Servers (Destination U-Turn NAT)
- Enable Bi-Directional Address Translation for Your Public-Facing Servers (Static Source NAT)
- Configure Destination NAT with DNS Rewrite
- Configure Destination NAT Using Dynamic IP Addresses
- Modify the Oversubscription Rate for DIPP NAT
- Reserve Dynamic IP NAT Addresses
- Disable NAT for a Specific Host or Interface
-
- Network Packet Broker Overview
- How Network Packet Broker Works
- Prepare to Deploy Network Packet Broker
- Configure Transparent Bridge Security Chains
- Configure Routed Layer 3 Security Chains
- Network Packet Broker HA Support
- User Interface Changes for Network Packet Broker
- Limitations of Network Packet Broker
- Troubleshoot Network Packet Broker
-
- Enable Advanced Routing
- Logical Router Overview
- Configure a Logical Router
- Create a Static Route
- Configure BGP on an Advanced Routing Engine
- Create BGP Routing Profiles
- Create Filters for the Advanced Routing Engine
- Configure OSPFv2 on an Advanced Routing Engine
- Create OSPF Routing Profiles
- Configure OSPFv3 on an Advanced Routing Engine
- Create OSPFv3 Routing Profiles
- Configure RIPv2 on an Advanced Routing Engine
- Create RIPv2 Routing Profiles
- Create BFD Profiles
- Configure IPv4 Multicast
- Configure MSDP
- Create Multicast Routing Profiles
- Create an IPv4 MRoute
-
-
PAN-OS 11.2
- PAN-OS 11.2
- PAN-OS 11.1
- PAN-OS 11.0 (EoL)
- PAN-OS 10.2
- PAN-OS 10.1
- PAN-OS 10.0 (EoL)
- PAN-OS 9.1 (EoL)
- PAN-OS 9.0 (EoL)
- PAN-OS 8.1 (EoL)
- Cloud Management and AIOps for NGFW
Configure an Aggregate Ethernet Interface Variable
Learn more about configuring an Aggregate Ethernet (AE) interface variable in
snippets and folders, which allows you to reuse the common configuration across the entire
deployment.
| Where Can I Use This? | What Do I Need? |
|---|---|
|
One of these:
|
Configuring an Aggregate Ethernet (AE) interface variable in snippets or folders
allows you to have reusable common configuration across the entire deployment.
Aggregate Ethernet interface variable reduces duplication of configuration and
significantly simplifies the process of updating and maintaining common
configurations.
- Before configuring an Aggregate Ethernet (AE) interface variable, you must configure the Aggregate Ethernet interface group.
- Log in to Strata Cloud Manager.
- Select ManageConfigurationNGFW and Prisma AccessDevice SettingsInterfacesEthernet and expand the Configuration Scope to view the Config Tree.
- Add the interface.
- For Folders and Snippets, Add InterfaceInterface.
- For Firewalls, AddAdd Interface.
- If you’re configuring an Ethernet interface for a specific firewall, select the interface you want to configure instead.
- Configure the interface.
- Enter the Interface Name.
- (Folders and Snippets only) Select the Default Interface Assignment.
- (Optional) Enter a Descriptionfor the interface.
- For Interface Type, select Aggregate Ethernet.
- Assign the interface to an Aggregate Group.
- Optional Expand Advanced Settings and configure the interface link settings.
- Select the interface Link Speed in Mbps (10, 100, 1000, 10000, 20000, 25000, 40000, 50000, 100000, 200000, or 400000), or select auto to have the firewall automatically determine the speed.
- Select whether the Link Duplex transmission mode is full-duplex (full), half-duplex (half), or negotiated automatically (auto).By default, auto is selected by default to allow the firewall to negotiate the transmission mode automatically.
- Select whether the interface Link State is enabled (Force to up), disabled (Force to down), or determined automatically (Auto Detect).Auto detect is selected by default to allow the firewall to determine the link state.
- Configure Power over Ethernet (PoE) on the interfaces of supported firewalls to transfer electrical power from the firewall to a connected powered device.
- The PoE Enabled is selected by default if the PoE is active on ports.
- Set the amount of PoE Reserved Power by the port in Watts. This value must be a number between 0 and the Maximum Reserved Power of the port. A 0 indicates that no power is reserved by that PoE port.
- Set the LACP Port Priority.The firewall only uses this field if you enabled the Link Aggregation Control Protocol for the aggregate group. If the number of interfaces you assign to the group exceeds the number of active interfaces, the firewall uses the LACP port priorities of the interfaces to determine which are in standby mode. The lower the numeric value, the higher the priority (range is 1-65,535; default is 32,768).
- Save.
- Push Config to push your configuration changes.