Create a High-Bandwidth Remote Network Connection
Focus
Focus

Create a High-Bandwidth Remote Network Connection

Table of Contents

Create a High-Bandwidth Remote Network Connection

To create a high-bandwidth remote network connection, complete the following task.
  1. in Panorama, configure the Prisma Access remote network tunnels.
    1. (
      Optional
      ) if you haven’t already, set up IKE gateways, IKE crypto and IPSec crypto profiles, and IPSec tunnels for the remote network connections you create.
      Make a note of the IKE and IPSec cryptographic profiles; you specify the same settings on the CPE you use to terminate the remote network connection in the remote network location.
    2. Determine the type of remote network deployment you have.
      Prisma Access deployments allocate bandwidth by allocating bandwidth per compute location or by allocating bandwidth by location.
    3. Onboard the remote network.
      • To onboard the remote network that allocates bandwidth by compute location:
        1. Allocate bandwidth for the locations that you want to onboard by clicking the gear icon in the
          Bandwidth Allocation
          area.
        2. Enter the
          Bandwidth Allocation
          you want for each
          Compute Location
          that is associated with the
          Prisma Access Locations
          you want to onboard.
        3. Wait for the bandwidth to be reflected in the
          Allocated Total
          field at the top of the page; then, click
          OK
          .
      • To onboard the remote network that allocates bandwidth by location, continue to the next step; you allocate bandwidth during remote network onboarding.
    4. Select
      Panorama
      Cloud Services
      Configuration
      Remote Networks
      and create four remote network connections, specifying the following settings:
      • Select the same
        Location
        for each connection.
      • Select the
        IPSec Termination Node
        .
        Select a separate IPSec termination node for each remote network connection.
        If you have a deployment that allocates bandwidth by location, select a
        Bandwidth
        of
        500 Mbps
        .
        The bandwidth you select cannot exceed the total amount of bandwidth you have licensed. Use this setting to define the amount of the total licensed bandwidth you want to allocate to this location.
      • Enable
        BGP,
        Advertise Default Route
        , and
        Don’t Advertise Prisma Access Routes
        .
      • Specify the same
        Peer AS
        for all remote network connections.
        This example shows a
        Peer AS
        of 2000; in this example, you select a
        Peer AS
        of 2000 for all four connections.
      • (
        Optional
        ) if you want to create a backup remote network, create one by selecting
        Enable Secondary WAN
        ; then, select the
        IPSec Tunnel
        you created for the backup tunnel.
      Configuring a Secondary WAN is not supported in the following deployments:
      • If your secondary WAN is set up in active-active mode with the Primary IPSec tunnel.
      • If your customer premises equipment (CPE) is set up in an Equal Cost Multipath (ECMP) configuration with the Primary and Secondary IPSec tunnel.
      When complete, you have four 500 Mbps remote network connections for the same location. If you configured backup tunnels, you also have four secondary tunnels to be used for failover purposes.
    5. Select
      Panorama
      Cloud Services
      Status
      Network Details
      Remote Networks
      and make a note of the
      Service IP Address
      and
      EBGP Router
      addresses.
      You use the
      Service IP Address
      as the peer IP address when you configure the IPSec tunnel on the CPE in the remote network site, and you use these addresses and the
      EBGP Router
      addresses when you create static routes on the CPE.
  2. On the CPE in the remote network site, configure the remote network tunnels.
    • The configuration in these steps use Palo Alto Networks next-generation firewalls; you can use any CPE device that supports IPSec tunnels and ECMP for this deployment.
    • Bandwidth balancing depends on CPE hashing for ECMP. However, Prisma Access ensures symmetrical return of traffic.
    1. Create four active tunnels from the active CPE to each of the four network connections. For the
      Peer IP
      address, enter the
      Service IP Address
      of the remote network you received from Prisma Access in Step 5.
    2. (
      Optional
      ) If you create backup tunnels, create them from the active CPE to each of the four network connections. For the
      Peer IP
      address, enter the
      Service IP Address
      of the remote network you received from Prisma Access in Step 5.
  3. Configure ECMP on the CPE in the remote network site.
    1. Select
      Network
      Virtual Routers
      .
    2. Select the
      default
      virtual router, or
      Add
      a new virtual router.
    3. Select
      Router Settings
      Enable
      ECMP
      , then
      Enable
      ECMP with a
      Max Path
      of
      4
      and a load balance
      Method
      of
      Balanced Round Robin
      .
  4. On the CPE in the remote network site, create static routes to the Prisma Access
    Service IP Address
    and
    EBGP Router
    IP addresses you retrieved in Step 5.
    As previously stated, dynamic routing with BGP is required for this configuration. To facilitate BGP connection between the CPE and Prisma Access’ eBGP router, you need to add a static route for the eBGP router IP address on the CPE, and the next-hop must be the tunnel interface on the CPE. You must repeat this step for all other Remote Network eBGP router IP addresses on remaining tunnels.
    The following example shows the route on the active CPE. If you created backup tunnels on a standby CPE, create the same routing on the standby CPE.
    If you are configuring a Palo Alto Networks next-generation firewall, select
    Static Routes
    IPv4
    to add the static routes.
  5. Enable route redistribution on the CPE by selecting
    Redistribution Profile
    IPv4
    , then
    Add
    an IPv4 route redistribution profile.
  6. Select
    BGP
    Peer Group
    ,
    Enable
    BGP on the virtual router instance, then
    Add
    Remote Network BGP peers.
  7. Select
    BGP
    Redist Rules
    , then attach the route redistribution profile you created in Step 5.
  8. Validate that the CPE is passing traffic on all four of its tunnels.
  9. Check the status of the ECMP-enabled connections from Prisma Access.
    • Select
      Panorama
      Cloud Services
      Monitor
      Remote Networks
      , select the region where you deployed the ECMP connections, then select
      Status
      .
      • In this area,
        ECMP
        displays as
        No
        . This is expected because you are not configuring the Prisma Access ECMP load balancing feature.
      • ECMP is directional from CPE to Prisma Access and Prisma Access ensures symmetrical return of the traffic from the CPE.
    • Select
      Statistics
      to see that traffic is passing through each remote network tunnel.
    When you have completed this workflow, you have created a high-bandwidth configuration for the remote network. Keep in mind that this solution is supported for outbound traffic only.

Recommended For You