Prisma Access
VMware SD-WAN by VeloCloud Solution Guide
Table of Contents
VMware SD-WAN by VeloCloud Solution Guide
Where Can I Use This? | What Do I Need? |
|---|---|
|
|
The following sections describe how you use the VMware SD-WAN by VeloCloud
(VeloCloud) with Prisma Access:
Supported IKE and IPSec Cryptographic Profiles
The following table documents the IKE/IPSec crypto settings that are supported with
Prisma Access and VeloCloud devices. Use the recommended settings when you onboard a
remote network and define IKE and IPSec cryptographic settings when connecting the
Prisma Access and VeloCloud device.
A check mark indicates that the profile or architecture type is supported; a dash (—)
indicates that it is not supported. Default and Recommended settings are noted in
the table.
Crypto Profiles | Prisma Access | VeloCloud | |
|---|---|---|---|
Tunnel Type | IPSec Tunnel | √ | √ |
GRE Tunnel | — | — | |
Routing | Static Routes | √ | √ |
Dynamic Routing (BGP) | √ | — | |
Dynamic Routing (OSPF) | — | — | |
IKE Versions | IKE v1 | √ | √ |
IKE v2 | √ | √ | |
IPSec Phase 1 DH-Group | Group 1 | √ | √ |
Group 2 | √ | √ | |
Group 5 | √ | √ | |
Group 14 | √ | √ | |
Group 19 | √ | — | |
Group 20 | √ | — | |
IPSec Phase 1 Auth If you use
IKEv2 with certificate-based authentication, only SHA1 is
supported in IKE crypto profiles (Phase 1). | MD5 | √ | √ |
SHA1 | √ | √ | |
SHA256 | √ | √ | |
SHA384 | √ | — | |
SHA512 | √ | — | |
IPSec Phase 1 Encryption | DES | √ | — |
3DES | √ | — | |
AES-128-CBC | √ | √ | |
AES-192-CBC | √ | — | |
AES-256-CBC | √ | √ | |
IPSec Phase 1 Key Lifetime Default | √ | √ | |
IPSec Phase 1 Peer
Authentication | Pre-Shared Key | √ | √ |
Certificate | √ | — | |
IKE Peer Identification | FQDN | √ | √ |
IP Address | √ | — | |
User FQDN | √ | — | |
IKE Peer | As Static Peer | √ | √ |
As Dynamic Peer | √ | — | |
Options | NAT Traversal | √ | √ |
Passive Mode | √ | √ | |
Ability to Negotiate
Tunnel | Per Subnet Pair | √ | — |
Per Pair of Hosts | √ | — | |
Per Gateway Pair | √ | — | |
IPSec Phase 2 DH-Group | Group 1 | √ | — |
Group 2 | √ | √ | |
Group 5 | √ | √ | |
Group 14 | √ | √ | |
Group 19 | √ | — | |
Group 20 | √ | — | |
No PFS | √ | — | |
IPSec Phase 2 Auth | MD5 | √ | √ |
SHA1 | √ | √ | |
SHA256 | √ | √ | |
SHA384 | √ | — | |
SHA512 | √ | — | |
None | √ | — | |
IPSec Phase 2 Encryption | DES | √ | — |
3DES | √ | — | |
AES-128-CBC | √ | √ | |
AES-192-CBC | √ | — | |
AES-256-CBC | √ | √ | |
AES-128-CCM | √ | — | |
AES-128-GCM | √ | — | |
AES-256-GCM | √ | — | |
NULL | √ | — | |
IPSec Protocol | ESP | √ | √ |
AH | √ | — | |
IPSec Phase 2 Key Lifetime Default | √ | √ | |
Tunnel Monitoring
Fallback | Dead Peer Detection (DPD) | √ | √ |
ICMP | — | — | |
Bidirectional Forwarding Detection (BFD) | — | — | |
SD-WAN Architecture Type | With Regional Hub/Gateway/Data Center | N/A | √ |
No Regional Hub/Gateway/Data Center | NA | √ | |
SD-WAN Deployment Architectures Supported by VMware SD-WAN
The VMware VeloCloud SD-WAN supports the following deployment architectures for use
with Prisma Access. a dash (—) indicates that the deployment is not supported.
Use Case | Architecture | Supported? |
|---|---|---|
Securing traffic from each branch site with 1 WAN
link (Type 1) |  | √ |
Securing branch and HQ sites with active/backup
SD-WAN connections |  | √ |
Securing branch and HQ sites with active/active
SD-WAN connections |  | — |
Securing branch and HQ sites with SD-WAN edge devices
with a primary and secondary tunnel |  | √ |
Securing SD-WAN deployments with Regional Hub/POP
architecture (Type 2) |  | √ |