Configure IoT SNMP Start Nodes
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
- Prisma SD-WAN Incidents and Alerts
Configure IoT SNMP Start Nodes
Learn how to configure IoT SNMP start nodes in
Prisma SD-WAN
.Where Can I Use
This? | What Do I
Need? |
|---|---|
|
|
You can configure a branch site ION device or a DC ION device as a start
node for the discovery process. In this configuration you can specify a list of IP
addresses (IPv4) that can be used as the start address for network discovery and
subsequent device discovery.
Each site supports a maximum of 128 such starting endpoints. It also
supports a scope (per starting address) that limits the discovery to a set of
devices within the specified scope. The IP addresses configured in the list should
be reachable from the ION devices that are associated with the site.
- SelectSites, select a site and clickConfigure IoT SNMP Start Nodes.
- Add aName.
- Enter aStart Node.This is the IP address that the ION device uses as a starting point for network and device discovery.
- (Optional)Enter aDescriptionandTags.
- (Optional)Enter separate subnets forSubnets Scope.A maximum of eight subnets can be entered per start node. This limits the discovery to a set of devices within the specified scope.
- ClickSave.