Set up IoT Security and Cortex XSOAR for SNMP Discovery

Set up IoT Security and Cortex XSOAR to integrate with network switches for SNMP discovery.
To set up IoT Security to integrate through Cortex XSOAR with network switches, you must add a Cortex XSOAR engine to your network.
You must also configure one or more SNMP integration instances in XSOAR. To do this, you need the IP address of the entry switch and the SNMP community string for read-only access.

Cortex XSOAR Engine Installation

The Cortex XSOAR engine initiates connections to switches and to the Cortex cloud and provides the means through which they communicate with each other. Although it's possible to install an XSOAR engine on machines running Windows, macOS, and Linux operating systems, only an engine on a Linux machine supports IoT Security integrations. For more information about operating system and hardware requirements, see the Cortex XSOAR Administrator’s Guide.
We recommend downloading the XSOAR engine using the shell installer script and installing it on a Linux machine. This simplifies the deployment by automatically installing all required dependencies and also enables remote engine upgrades.
When placing the XSOAR engine on your network, make sure it can form SNMP connections to your switches on UDP port 161.
The firewall must also allow the engine to form HTTPS connections on TCP port 443 to the Cortex cloud at https://<your-domain>.iot.demisto.live/. You can see the URL of your XSOAR instance when you log in to the IoT Security portal and click
Integrations
Launch Cortex XSOAR
. It’s visible in the address bar of the web page displaying the XSOAR interface.
To create an XSOAR engine, access the Cortex XSOAR interface (from the IoT Security portal, click
Integrations
Launch Cortex XSOAR
). Click
Settings
Engines
Create New Engine
. Choose
Shell
as the type.
For installation instructions, see Install Cortex XSOAR Engines.

Configure IoT Security and Cortex XSOAR

  1. Log in to IoT Security and from there access SNMP settings in Cortex XSOAR.
    1. Log in to IoT Security and then click
      Integrations
      .
    2. IoT Security uses Cortex XSOAR to get device information from network switches using SNMP, and the settings you must configure to integrate with it are in the XSOAR interface. To access these settings, click
      Launch Cortex XSOAR
      .
      The Cortex XSOAR interface opens in a new browser window.
    3. Click
      Settings
      in the left navigation menu, search for
      snmp
      to locate it among other instances.
  2. Configure the SNMP instance.
    1. Click
      Add instance
      to open the settings panel.
    2. Enter the following settings and leave the other settings at their default values:
      Name
      : Use the default name of the instance (SNMP_instance_1) or enter a new one.
      Entry switch IP
      : Enter the IP address of the entry switch with which to begin the SNMP discovery process.
      SNMP Version
      : Choose the SNMP version that your switches support, either
      2c
      (SNMPv2c) or
      3
      (SNMPv3). If you choose
      2c
      , configure the Community String and Use a single engine settings. If you choose
      3
      , configure the Username, Security Level, Authentication Protocol and Password, and Privacy Protocol and Password settings.
      Community String
      (for SNMPv2c): Enter the SNMP community string configured on the switches to permit read-only access.
      Username
      (for SNMPv3): Enter a username for an SNMP user account with read-only access. This is the account XSOAR uses when accessing an SNMP server running on a switch. The security level and authentication password defined below are also associated with this user account.
      Security Level
      (for SNMPv3): Choose the security level for accessing an SNMP server on a switch.
      • noAuthNoPriv
        : Choose this to not exchange passwords for user authentication and not encrypt communications between the SNMP agent on XSOAR and an SNMP server on a switch.
      • authNoPriv
        : Choose this to require user authentication based on either MD5 or SHA hashes and not encrypt communications between XSOAR and the switches.
      • authPriv
        : Choose this to require both user authentication and encryption.
      Authentication Protocol
      (for SNMPv3): Choose the algorithm for authenticating communications between XSOAR and the switches:
      MD5
      (Message Digest Algorithm 5) or
      SHA
      for SHA-1 (Secure Hash Algorithm 1).
      Authentication Password
      (for SNMPv3): Enter the password used during the authentication process.
      Privacy Protocol
      (for SNMPv3): Choose the algorithm for encrypting communications between XSOAR and the switches:
      DES
      (Data Encryption Standard) or
      AES
      (Advanced Encryption Standard).
      Privacy Password
      (for SNMPv3): Enter the password used during the encryption process.
    3. Run on Single engine
      : Choose the XSOAR engine that you installed previously.
    4. When finished, click
      Run test
      or
      Test
      .
      If the test is successful, a Success message appears. If not, check that the settings were entered correctly and then test the configuration again.
    5. After the test succeeds, click
      Save & exit
      to save your changes and close the settings panel.
  3. To enable the SNMP integration instance, click
    Enable
    .
    You can add multiple SNMP integration instances, each one with settings for the same or a different XSOAR engine to communicate with a different entry switch. To add another instance, click
    Add instance
    .
  4. Create a job that periodically queries switches for device attributes from network switches.
    This job periodically queries switches for device data and updates the IoT Security inventory.
    1. Click
      Jobs
      near the bottom of the left navigation menu to open the Jobs page.
    2. Click
      New Job
      at the top of the Jobs page.
    3. Enter the following and leave the other fields at their default values:
      Recurring
      : Select this because you want to periodically query switches for device information.
      Every
      : Enter a number and set the interval value (Minutes, Hours, Days, or Weeks) and select the days on which to run the job. This determines how often XSOAR queries switches for details about active devices. For example:
      24 Hours
      Name
      : Type a name for the job such as
      SNMP Discovery 1
      .
      Playbook
      :
      Incremental SNMP data import to PANW IoT Cloud - PANW IoT 3rd party Integration
      Integration Instance Name
      : Enter the name of the SNMP integration instance you defined earlier. For example:
      SNMP_instance_1
    4. Click
      Create new job
      .
      The job appears in the Jobs list.
  5. Enable the job and run it.
    1. Check the Job Status for the job you created. If it’s Disabled, select its check box and then click
      Enable
      .
    2. After you enable it, keep the check box selected and click
      Run now
      . The Run Status changes from Idle to Running.
      At the defined interval, XSOAR begins querying the network switches for device information, which it then forwards to the IoT Security cloud.
  6. If you created more integration instances for multiple switches, add more instances as necessary.
    Each SNMP instance requires a separate job.
  7. When done, return to the IoT Security portal and check the status of the SNMP integration.
    Three states can appear in the Status column on the Integrations page.
    • Disabled
      means that either the integration was never configured (its default state) or it was configured but intentionally disabled.
    • Inactive
      means that the integration was configured and enabled but is not currently running.
    • Active
      means that the integration was configured, enabled and is currently active.
    When you see that its status is
    Active
    , the setup for IoT Security/Cortex XSOAR integration for SNMP discovery is complete. At the defined interval, XSOAR begins the job by first querying the entry switch for device information, which it forwards to the IoT Security cloud, and then querying neighbor switches.

Recommended For You