Configure an Aggregate Interface Group
An aggregate interface group uses IEEE 802.1AX link aggregation to combine multiple Ethernet interfaces into a single virtual interface that connects the firewall to another network device or firewall. An aggregate group increases the bandwidth between peers by load balancing traffic across the combined interfaces. It also provides redundancy; when one interface fails, the remaining interfaces continue supporting traffic.
By default, interface failure detection is automatic only at the physical layer between directly connected peers. However, if you enable Link Aggregation Control Protocol (LACP), failure detection is automatic at the physical and data link layers regardless of whether the peers are directly connected. LACP also enables automatic failover to standby interfaces if you configured hot spares. All Palo Alto Networks firewalls except VM-Series models support aggregate groups. The Product Selection tool indicates the number of aggregate groups each firewall supports. Each aggregate group can have up to eight interfaces.
PAN-OS firewall models support a maximum of 16,000 IP addresses assigned to physical or virtual Layer 3 interfaces; this maximum includes both IPv4 and IPv6 addresses.
QoS is supported on only the first eight aggregate groups.
Before configuring an aggregate group, you must configure its interfaces. Among the interfaces assigned to any particular aggregate group, the hardware media can differ (for example, you can mix fiber optic and copper), but the bandwidth and interface type must be the same. The bandwidth and interface type options are:
- Bandwidth—1Gbps, 10Gbps, 40Gbps, or 100Gbps.
- Interface type—HA3, virtual wire, Layer 2, or Layer 3.
This procedure describes configuration steps only for the Palo Alto Networks firewall. You must also configure the aggregate group on the peer device. Refer to the documentation of that device for instructions.
- Configure the general interface group parameters.
- SelectandNetworkInterfacesEthernetAdd Aggregate Group.
- In the field adjacent to the read-onlyInterface Name, enter a number (1–8) to identify the aggregate group.
- For theInterface Type, selectHA,Virtual Wire,Layer2, orLayer3.
- Configure the remaining parameters for theInterface Typeyou selected.
- Configure the LACP settings.Perform this step only if you want to enable LACP for the aggregate group.You cannot enable LACP for virtual wire interfaces.
- Select theLACPtab andEnable LACP.
- Set theModefor LACP status queries toPassive(the firewall just responds—the default) orActive(the firewall queries peer devices).As a best practice, set one LACP peer to active and the other to passive. LACP cannot function if both peers are passive. The firewall cannot detect the mode of its peer device.
- Set theTransmission Ratefor LACP query and response exchanges toSlow(every 30 seconds—the default) orFast(every second). Base your selection on how much LACP processing your network supports and how quickly LACP peers must detect and resolve interface failures.
- SelectFast Failoverif you want to enable failover to a standby interface in less than one second. By default, the option is disabled and the firewall uses the IEEE 802.1ax standard for failover processing, which takes at least three seconds.As a best practice, useFast Failoverin deployments where you might lose critical data during the standard failover interval.
- Enter theMax Ports(number of interfaces) that are active (1 to 8) in the aggregate group. If the number of interfaces you assign to the group exceeds theMax Ports, the remaining interfaces will be in standby mode. The firewall uses theLACP Port Priorityof each interface you assign (Step 3) to determine which interfaces are initially active and to determine the order in which standby interfaces become active upon failover. If the LACP peers have non-matching port priority values, the values of the peer with the lowerSystem Prioritynumber (default is 32,768; range is 1 to 65,535) will override the other peer.
- (Optional) For active/passive firewalls only, selectEnable in HA Passive Stateif you want to enable LACP pre-negotiation for the passive firewall. LACP pre-negotiation enables quicker failover to the passive firewall (for details, see LACP and LLDP Pre-Negotiation for Active/Passive HA).If you select this option, you cannot selectSame System MAC Address for Active-Passive HA; pre-negotiation requires unique interface MAC addresses on each HA firewall.
- (Optional) For active/passive firewalls only, selectSame System MAC Address for Active-Passive HAand specify a singleMAC Addressfor both HA firewalls. This option minimizes failover latency if the LACP peers are virtualized (appearing to the network as a single device). By default, the option is disabled: each firewall in an HA pair has a unique MAC address.If the LACP peers are not virtualized, use unique MAC addresses to minimize failover latency.
- Assign interfaces to the aggregate group.Perform the following steps for each interface (1–8) that will be a member of the aggregate group.
- Selectand click the interface name to edit it.NetworkInterfacesEthernet
- Set theInterface TypetoAggregate Ethernet.
- Select theAggregate Groupyou just defined.
- Select theLink Speed,Link Duplex, andLink State.As a best practice, set the same link speed and duplex values for every interface in the group. For non-matching values, the firewall defaults to the higher speed and full duplex.
- (Optional) Enter anLACP Port Priority(default is 32,768; range is 1 to 65,535) if you enabled LACP for the aggregate group. If the number of interfaces you assign exceeds theMax Portsvalue of the group, the port priorities determine which interfaces are active or standby. The interfaces with the lower numeric values (higher priorities) will be active.
- If the firewalls have an active/active configuration and you are aggregating HA3 interfaces, enable packet forwarding for the aggregate group.
- Selectand edit the Packet Forwarding section.DeviceHigh AvailabilityActive/Active Config
- Select the aggregate group you configured for theHA3 Interfaceand clickOK.
- Commit your changes and verify the aggregate group status.
- Verify that the Link State column displays a green icon for the aggregate group, indicating that all member interfaces are up. If the icon is yellow, at least one member is down but not all. If the icon is red, all members are down.
- If you configured LACP, verify that the Features column displays the LACP enabled icon for the aggregate group.
Recommended For You
Recommended videos not found.