Install Content Updates
To ensure that you are always protected from the latest threats (including those that have not yet been discovered), you must ensure that you keep your firewalls up-to-date with the latest content and software updates published by Palo Alto Networks. The Dynamic Content Updates available to you depend on which subscriptions you have.
Follow these steps to install content updates. You can also set a schedule for content updates, to define the frequency at which the firewall retrieves and installs updates.
Applications and Threats content updates work a little differently than other update types—to get the most out of the latest application knowledge and threat prevention, follow the guidelines to Deploy Applications and Threats Content Updates instead of the steps here.
- Ensure that the firewall has access to the update server.
- By default, the firewall accesses theUpdate Serveratupdates.paloaltonetworks.comso that the firewall receives content updates from the server to which it is closest. If your firewall has limited access to the Internet, it might be necessary to configure your allow list to enable access to servers involved in update downloads. For more information about content update servers, refer to Content Delivery Network Infrastructure for Dynamic Updates. If you want additional reference information or are experiencing connectivity and update download issues, please refer to https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA14u0000001UtRCAU.If your device is located in mainland China, Palo Alto Networks recommends using theupdates.paloaltonetworks.cnserver for update downloads.
- (Optional) ClickVerify Update Server Identityfor an extra level of validation to enable the firewall to check that the server’s SSL certificate is signed by a trusted authority. This is enabled by default.
- (Optional) If the firewall needs to use a proxy server to reach Palo Alto Networks update services, in theProxy Serverwindow, enter:
- Server—IP address or host name of the proxy server.
- Port—Port for the proxy server. Range: 1-65535.
- User—Username to access the server.
- Password—Password for the user to access the proxy server. Re-enter the password atConfirm Password.
- (Optional) Configure up to three reconnection attempts if a connection failure occurs. Usedebug set-content-download-retry attemptsto set the number of connection attempts. The default is 0.
- Check for the latest content updates.Selectand clickDeviceDynamic UpdatesCheck Now(located in the lower left-hand corner of the window) to check for the latest updates. The link in theActioncolumn indicates whether an update is available:
You cannot download the antivirus update until you have installed the Application and Threats update.
- Download—Indicates that a new update file is available. Click the link to begin downloading the file directly to the firewall. After successful download, the link in theActioncolumn changes fromDownloadtoInstall.
- Revert—Indicates that a previously installed version of the content or software version is available. You can choose to revert to the previously installed version.
- Install the content updates.Installation can take up to 10 minutes on a PA-220 firewall and up to two minutes on a PA-5200 Series, PA-7000 Series, or VM-Series firewall.Click theInstalllink in theActioncolumn. When the installation completes, a check mark displays in theCurrently Installedcolumn.
- Schedule each content update.Repeat this step for each update you want to schedule.Stagger the update schedules because the firewall can only download one update at a time. If you schedule the updates to download during the same time interval, only the first download will succeed.
- Set the schedule of each update type by clicking theNonelink.
- Specify how often you want the updates to occur by selecting a value from theRecurrencedrop-down. The available values vary by content type (WildFire updates are available inReal-time,Every Minute,Every 15 Minutes,Every 30 minutes, orEvery Hourwhereas Applications and Threats updates can be scheduled forWeekly,Daily,Hourly, orEvery 30 Minutesand Antivirus updates can be scheduled forHourly,Daily, orWeekly).
- Specify theTimeand (or, minutes past the hour in the case of WildFire), if applicable depending on theRecurrencevalue you selected,Dayof the week that you want the updates to occur.
- Specify whether you want the system toDownload Onlyor, as a best practice,Download And Installthe update.
- Enter how long after a release to wait before performing a content update in theThreshold (Hours)field. In rare instances, errors in content updates may be found. For this reason, you may want to delay installing new updates until they have been released for a certain number of hours.If you have mission critical applications that must be 100% available, set the threshold for Applications or Applications and Threats updates to a minimum of 24 hours or more and follow the Best Practices for Applications and Threats Content Updates. Additionally, While scheduling content updates is a one-time or infrequent task, after you’ve set the schedule, you’ll need to continue to Manage New and Modified App-IDs that are included in content releases, as these App-IDs can change how security policy is enforced.
- (Optional) Enter theNew App-ID Thresholdsin hours to set the amount of time the firewall waits before installing content updates that contain new App-IDs.
- ClickOKto save the schedule settings.
- ClickCommitto save the settings to the running configuration.
Recommended For You
Recommended videos not found.