Configure Active/Passive HA
Focus
Focus
Next-Generation Firewall

Configure Active/Passive HA

Table of Contents

Configure Active/Passive HA

Learn how to configure active/passive HA pair of firewalls and HA.
Where Can I Use This?What Do I Need?
  • NGFW
For Strata Cloud Manager managed NGFWs:
  • Strata Cloud Manager Pro
The following procedure shows how to configure a pair of firewalls in an active/passive deployment as depicted in the following example topology.
Active/Passive High Availability (HA) provides firewall redundancy by maintaining two firewalls in a primary-secondary relationship, where one firewall actively processes traffic while the other remains in standby mode, ready to assume control if the primary firewall fails. In an Active/Passive HA deployment, the active firewall handles all network traffic and maintains the runtime state, while the passive firewall continuously synchronizes its configuration and session information with the active unit. When a failover event occurs—whether due to hardware failure, software issues, or network connectivity problems—the passive firewall seamlessly transitions to the active role, ensuring minimal service disruption and maintaining network security policies. This configuration is ideal for environments that require high availability but do not need the increased throughput that Active/Active HA provides, making it a cost-effective solution for ensuring business continuity while maintaining a single point of traffic processing.
HA Active/Passive Support for PA-7500 and PA-5500 Series Firewalls
High Availability active/passive mode, which provides firewall redundancy and failover capabilities, is supported on PA-7500 series firewalls beginning with PAN-OS 12.1.5 and on PA-5500 series firewalls beginning with PAN-OS 12.1.7.
The firewalls support only HA active/passive mode; HA active/active mode is not supported. HA active/passive includes comprehensive network integration features such as LACP, link monitoring, and session synchronization functionality. LACP is supported on both Layer 2 and Layer 3 aggregate interfaces, including LACP pre-negotiation capabilities that enable the passive device to establish link aggregation readiness and reduce failover times. Link and path monitoring is supported for network health assessments. HA active/passive also maintains full runtime synchronization of session state between active and passive devices, ensuring that active sessions can continue uninterrupted during failover events and that the standby device maintains current awareness of all network connections and their associated state information.
On PA-7500 and PA-5500 series firewalls, HA active/passive uses dedicated High-Speed Chassis Interconnect (HSCI) interfaces for all HA communications and maintains session state synchronization between the active and passive devices.
  • HA1 Control Link: Carries heartbeat messages, configuration synchronization, and state information between HA peers.
  • HA2 Data Link: Synchronizes session tables and forwarding information between firewalls.
  • Layer 2 Transport: All HA traffic uses Layer 2 connectivity over HSCI interfaces.
You cannot configure HA and NGFW clustering simultaneously on the same firewall.
The HSCI interface assignments for HA links follow a specific configuration pattern that ensures proper communication between HA peers. All HSCI traffic is transmitted in cleartext format. HA1 control link and HA2 data link are supported only on layer 2. The primary HA1 control link can only be configured on HSCI-A, while the HA1-backup link is restricted to HSCI-B, providing redundancy for critical control plane communications. Similarly, the HA2 data synchronization link can only be configured on HSCI-A, with the HA2-backup link assigned to HSCI-B for failover protection. While HSCI interfaces handle the primary HA communications, management interfaces can be configured to support heartbeat backup functionality, which provides an additional layer of split-brain prevention by maintaining minimal connectivity between HA peers through the management network when HSCI links become unavailable.
(PA-7500 and PA-5500 series firewalls)
  • HA active/passive mode on PA-7500 and PA-5500 series firewalls does not support encryption on HA1, HA2, or HA1/HA2 backup links. Therefore the HSCI-A and HSCI-B interfaces do not support encryption.
  • HA3 and HA4 interfaces are not supported and cannot be configured.
  • HA2 and HA2 backup interfaces only support Layer 2 (L2) connectivity.
  • MACsec functionality is not supported (unlike the clustering feature).
  • The HA1 and HA2 functions are aggregated on the HSCI-A and HSCI-B interface. The administrator cannot assign the front port interfaces to the HA1 or HA2 role.
  • The HSCI-A and HSCI-B operate exclusively at Layer 2 only and although you have to configure an IP address on these interfaces, they must reside on the same network.
  • IPv6 is not supported for HA1/HA2 interfaces. IPv4 addresses for HA1/HA2 is used exclusively for internal node-to-node communication. Both HA nodes must be configured on the same subnet.
  • PA-7500and PA-5500 firewalls require trunk mode (tagged traffic) for HSCI port connections when a switch is present in the connection path; access mode (untagged) is not supported in this configuration. If you are using a switch between HSCI connections, you must enable jumbo frames on the firewall and configure the switch ports as tagged ports. You should enable jumbo frames first, which will require a reboot if you're activating jumbo frames for the first time, and only then proceed to enable HA.
  • Panorama web interface may display configuration options that are not actually supported by PA-7500 and PA-5500 series firewalls. Always follow these documented constraints regardless of what appears in the interface.
    • Data ports cannot be configured for HA1, HA2, or HA1 and HA2 backup interfaces. Panorama may display these as selectable options, but they are not functional.
    • HSCI-A must be used for HA1 and HA2 primary interfaces. Other interface options may appear in Panorama but are not supported.
    • HSCI-B must be used for HA1/HA2 backup interfaces. Other interface options may appear in Panorama but are not supported.
The PA-7500 and PA-5500 Series firewalls utilize Condor 3 architecture, which introduces several key changes to the traditional High Availability (HA) active/passive configuration:
PA-7500 and PA-5500 Series firewalls uses management processor relay for HA communications. When restarting dataplanes on the firewall HA configurations, be aware that individual dataplane restarts will trigger a restart of the entire chassis to maintain HA consistency between peers.
(PA-7500 and PA-5500 series firewalls) The following additional parameters are required when configuring HA on active/passive mode:
  • (Mandatory) Device ID: A unique identifier (0 or 1) that must be configured differently on each HA peer to ensure proper HSCI port MAC address generation.
  • (Mandatory) Group ID: A numeric identifier ranging from 0 to 63 that must match on both HA peers. This ensures the devices recognize each other as part of the same HA pair. If the group IDs don't match, HA formation will fail and may result in split-brain scenarios.
  • (Optional) VLAN Configuration: VLAN tags (2-4094) for HSCI traffic, with VLAN 2 used as default for back-to-back connections.
(PA-7500 and PA-5500 series firewalls) Both the Device ID and Group ID are essential to ensure proper HSCI port MAC address generation. Misconfiguring either parameter will cause HA communication to fail. If there is a Device ID overlap, the devices will enter a split-brain state. If there is a Group ID mismatch, the devices will also enter a split-brain state without transitioning to a 'non-functional' state.

Configure Active/Passive HA (PAN-OS)

Configure your firewalls in an active/passive high availability (HA) configuration from PAN-OS and Panorama.
To configure an active/passive HA pair, first verify that any filtering devices between your HA pair members allow the protocols and ports used by the HA links, then complete the following workflows on the first firewall and repeat the steps on the second firewall.
  1. Connect the HA ports to set up a physical connection between the firewalls.
    • For firewalls with dedicated HA ports, use an Ethernet cable to connect the dedicated HA1 ports and the HA2 ports on peers. Use a crossover cable if the peers are directly connected to each other.
    • For firewalls without dedicated HA ports, select two data interfaces for the HA2 link and the backup HA1 link. Then, use an Ethernet cable to connect these in-band HA interfaces across both firewalls.
    Use the management port for the HA1 link and ensure that the management ports can connect to each other across your network.
  2. Enable ping on the management port.
    Enabling ping allows the management port to exchange heartbeat backup information.
    1. Select DeviceSetupInterfacesManagement.
    2. Select Ping as a service that is permitted on the interface.
  3. If the firewall does not have dedicated HA ports, set up the data ports to function as HA ports.
    For firewalls with dedicated HA ports continue to the next step.
    1. Select NetworkInterfaces.
    2. Confirm that the link is up on the ports that you want to use.
    3. Select the interface and set Interface Type to HA.
    4. Set the Link Speed and Link Duplex settings, as appropriate.
  4. Set the HA mode and group ID.
    1. Select DeviceHigh AvailabilityGeneral and edit the Setup section.
    2. Set a Group ID and optionally a Description for the pair. The Group ID uniquely identifies each HA pair on your network. If you have multiple HA pairs that share the same broadcast domain you must set a unique Group ID for each pair.
    3. Set the mode to Active Passive.
  5. Set up the control link connection.
    This example shows an in-band port that is set to interface type HA.
    For firewalls that use the management port as the control link, the IP address information is automatically pre-populated.
    1. In DeviceHigh AvailabilityHA Communications, edit Control Link (HA1).
    2. Select the Port that you have cabled for use as the HA1 link.
    3. Set the IPv4/IPv6 Address and Netmask.
      If the HA1 interfaces are on separate subnets, enter the IP address of the Gateway. Do not add a gateway address if the firewalls are directly connected or are on the same VLAN.
  6. (Optional) Enable encryption for the control link connection.
    This is typically used to secure the link if the two firewalls are not directly connected, that is if the ports are connected to a switch or a router.
    PA-7500 and PA-5500 Series firewalls use HSCI fabric for HA links that do not support SSH-based HA1 control link encryption. Because of this limitation, FIPS-CC mode and HA Active/Passive cannot be enabled together on these firewalls.
    You must choose one:
    • FIPS-CC mode (where HA Active/Passive will not be available), or
    • HA Active/Passive (where FIPS-CC mode will not be available).
    1. Export the HA key from one firewall and import it into the peer firewall.
      1. Select DeviceCertificate ManagementCertificates.
      2. Select Export HA key. Save the HA key to a network location that the peer can access.
      3. On the peer firewall, select DeviceCertificate ManagementCertificates, and select Import HA key to browse to the location that you saved the key and import it in to the peer.
      4. Repeat this process on the second firewall to exchange HA keys on both devices.
    2. Select DeviceHigh AvailabilityHA Communications, edit the Control Link (HA1) section.
    3. Select Encryption Enabled.
      If you enable encryption, after you finish configuring the HA firewalls, you can Refresh HA1 SSH Keys and Configure Key Options.
  7. Set up the backup control link connection.
    1. In DeviceHigh AvailabilityHA Communications, edit Control Link (HA1 Backup).
    2. Select the HA1 backup interface and set the IPv4/IPv6 Address and Netmask.
      PA-3200 Series firewalls don’t support an IPv6 address for the HA1 backup control link; use an IPv4 address.
  8. Set up the data link connection (HA2) and the backup HA2 connection between the firewalls.
    1. In DeviceHigh AvailabilityHA Communications, edit the Data Link (HA2) section.
    2. Select the Port to use for the data link connection.
    3. Select the Transport method. The default is ethernet, and will work when the HA pair is connected directly or through a switch. If you need to route the data link traffic through the network, select IP or UDP as the transport mode.
      UDP is the only supported transport mode in Azure environments. UDP is the preferred transport mode for PA-1400 Series and PA-3400 Series firewalls.
    4. If you use IP or UDP as the transport method, enter the IPv4/IPv6 Address and Netmask.
    5. Verify that Enable Session Synchronization is selected.
    6. Select HA2 Keep-alive to enable monitoring on the HA2 data link between the HA peers. If a failure occurs based on the threshold that is set (default is 10000 ms), the defined action will occur. For active/passive configuration, a critical system log message is generated when an HA2 keep-alive failure occurs.
      You can configure the HA2 keep-alive option on both firewalls, or just one firewall in the HA pair. If the option is only enabled on one firewall, only that firewall will send the keep-alive messages. The other firewall will be notified if a failure occurs.
    7. Edit the Data Link (HA2 Backup) section, select the interface, and add the IPv4/IPv6 Address and Netmask.
  9. Enable heartbeat backup if your control link uses a dedicated HA port or an in-band port.
    You do not need to enable heartbeat backup if you are using the management port for the control link.
    1. In DeviceHigh AvailabilityGeneral, edit the Election Settings.
    2. Select Heartbeat Backup.
      To allow the heartbeats to be transmitted between the firewalls, you must verify that the management port across both peers can route to each other.
      Enabling heartbeat backup also allows you to prevent a split-brain situation. Split brain occurs when the HA1 link goes down causing the firewall to miss heartbeats, although the firewall is still functioning. In such a situation, each peer believes that the other is down and attempts to start services that are running, thereby causing a split brain. When the heartbeat backup link is enabled, split brain is prevented because redundant heartbeats and hello messages are transmitted over the management port.
  10. Set the device priority and enable preemption.
    This setting is only required if you wish to make sure that a specific firewall is the preferred active firewall. For information, see Device Priority and Preemption.
    1. In DeviceHigh AvailabilityGeneral, edit the Election Settings.
    2. Set the numerical value in Device Priority. Make sure to set a lower numerical value on the firewall that you want to assign a higher priority to.
      If both firewalls have the same device priority value, the firewall with the lowest MAC address on the HA1 control link will become the active firewall.
    3. Select Preemptive.
      You must enable preemptive on both the active firewall and the passive firewall.
  11. (Optional) Modify the HA Timers.
    By default, the HA timer profile is set to the Recommended profile and is suited for most HA deployments.
    1. In DeviceHigh AvailabilityGeneral, edit the Election Settings.
    2. Select the Aggressive profile for triggering failover faster; select Advanced to define custom values for triggering failover in your set up.
      To view the preset value for an individual timer included in a profile, select Advanced and click Load Recommended or Load Aggressive. The preset values for your hardware model will be displayed on screen.
  12. (Optional) Modify the link status of the HA ports on the passive firewall.
    The passive link state is shutdown, by default. After you enable HA, the link state for the HA ports on the active firewall will be green and those on the passive firewall will be down and display as red.
    Setting the link state to Auto allows for reducing the amount of time it takes for the passive firewall to take over when a failover occurs and it allows you to monitor the link state.
    To enable the link status on the passive firewall to stay up and reflect the cabling status on the physical interface:
    1. In DeviceHigh AvailabilityGeneral, edit the Active Passive Settings.
    2. Set the Passive Link State to Auto.
      The auto option decreases the amount of time it takes for the passive firewall to take over when a failover occurs.
      Although the interface displays green (as cabled and up) it continues to discard all traffic until a failover is triggered.
      When you modify the passive link state, make sure that the adjacent devices do not forward traffic to the passive firewall based only on the link status of the firewall.
  13. Enable HA.
    1. Select DeviceHigh AvailabilityGeneral and edit the Setup section.
    2. Select Enable HA.
    3. Select Enable Config Sync. This setting enables the synchronization of the configuration settings between the active and the passive firewall.
    4. Enter the IP address assigned to the control link of the peer in Peer HA1 IP Address.
      For firewalls without dedicated HA ports, if the peer uses the management port for the HA1 link, enter the management port IP address of the peer.
    5. Enter the Backup HA1 IP Address.
  14. (PA-7500 and PA-5500 series firewalls) Configure unique Device ID as 0 or 1 on each HA peer.
  15. (Optional) (PA-7500 and PA-5500 series firewalls) You must specify the VLAN tag for L2 headers to ensure the configuration matches the supported VLAN tags on HSCI switches. Configure HSCI-A VLAN and HSCI-B VLAN.
    If you do not specify a value, the default VLAN tag of 2 will be applied to both ports. This default setting allows you to skip this configuration when devices are connected back-to-back, keeping your setup minimal.
  16. (Optional) Enable LACP and LLDP Pre-Negotiation for Active/Passive HA for faster failover if your network uses LACP or LLDP.
    Enable LACP and LLDP before configuring HA pre-negotiation for the protocol if you want pre-negotiation to function in active mode.
    1. Ensure that in Step 12you set the link state to Auto.
    2. Select NetworkInterfacesEthernet.
    3. To enable LACP active pre-negotiation:
      1. Select an AE interface in a Layer 2 or Layer 3 deployment.
      2. Select the LACP tab.
      3. Select Enable in HA Passive State.
      4. Click OK.
        You cannot also select Same System MAC Address for Active-Passive HA because pre-negotiation requires unique interface MAC addresses on the active and passive firewalls.
    4. To enable LACP passive pre-negotiation:
      1. Select an Ethernet interface in a virtual wire deployment.
      2. Select the Advanced tab.
      3. Select the LACP tab.
      4. Select Enable in HA Passive State.
      5. Click OK.
    5. To enable LLDP active pre-negotiation:
      1. Select an Ethernet interface in a Layer 2, Layer 3, or virtual wire deployment.
      2. Select the Advanced tab.
      3. Select the LLDP tab.
      4. Select Enable in HA Passive State.
      5. Click OK.
        If you want to allow LLDP passive pre-negotiation for a virtual wire deployment, perform Step d but do not enable LLDP itself.
  17. Save your configuration changes.
    Click Commit.
  18. After you finish configuring both firewalls, verify that the firewalls are paired in active/passive HA.
    1. Access the Dashboard on both firewalls, and view the High Availability widget.
    2. On the active firewall, click the Sync to peer link.
    3. Confirm that the firewalls are paired and synced, as shown as follows:
      • On the passive firewall: the state of the local firewall should display passive and the Running Config should show as synchronized.
      • On the active firewall: The state of the local firewall should display active and the Running Config should show as synchronized.

Configure Active/Passive HA (SCM)

Configure your firewalls in an active/passive high availability (HA) configuration from Strata Cloud Manager.
This feature is available on request. Contact your account team to enable the feature
Configure your firewalls in an active/passive high availability (HA) configuration from Strata Cloud Manager.
This procedure assumes you already onboarded the firewalls you want to configure in an active/passive HA configuration to Strata Cloud Manager and have added them to the same folder. Also verify that any filtering devices between your HA pair members allow the protocols and ports used by the HA links.
  1. Log in to Strata Cloud Manager.
  2. Select ConfigurationNGFW and Prisma Access and from Configuration Scope, select All Firewalls or the folder that the managed firewalls are associated with.
  3. Select Network & DeviceHA Setup.
  4. Create an HA Interface Profile.
    The HA Interface Profile defines the port assignments and IP addressing for the HA1 control link and HA2 data link. For Active-Active deployments, you can also configure the HA3 session synchronization link.
    Select HA Interface Profiles and click Add Interface Profile to create HA interface profiles.
    1. Enter a Name and Description for the profile.
    2. Configure the HA1 Interface settings for the primary device. The HA1 control link is used to exchange hellos, heartbeats, HA state information, and management plane synchronization for routing. This link is also used to synchronize configuration changes with its peer.
      • Select the Port, link speed, and link duplex for the HA1 control link on the primary HA peer. Port shows object interface variable in the configuration tree.
        Strata Cloud Manager interface may display configuration options that are not actually supported by PA-7500 series firewalls. Always follow these documented constraints regardless of what appears in the interface.
        • Data ports cannot be configured for HA1, HA2, or HA1 and HA2 backup interfaces. Strata Cloud Manager may display these as selectable options, but they are not functional.
        • HSCI-A must be used for HA1 and HA2 primary interfaces. Other interface options may appear in Strata Cloud Manager but are not supported.
        • HSCI-B must be used for HA1 and HA2 backup interfaces. Other interface options may appear in Strata Cloud Manager but are not supported.
      • Configure the variables for IP Address, Netmask, and Gateway. Variables show you all the variable tree up to the folder where you are configuring the HA interface profile. You can also create Variables and select it.
      • Enter the Monitor Hold Time (ms) that the firewall waits before declaring a peer failure due to a control link failure. Range is 1,000 to 60,000; default is 3,000.
      • Enable Encryption.
      • Configure the HA1 Backup Interface control link settings for the Secondary Device.
    3. On the HA2 tab, configure the HA2 data link settings.
      • Select the Ethernet Port for the HA2 data link on the primary device.
      • Enter the IP Address, Netmask, and Gateway of the HA2 data link for the primary HA peer.
      • (Optional) Configure HA2 Backup data link settings for redundancy.
    4. (Optional) On the HA3 tab, select the Port (HA3 Interface) for Active-Active deployments.
    5. Click Save.
  5. Select HA Group Profiles and click Add HA Group Profile.
    The HA Group Profile defines the HA mode, election settings, and heartbeat thresholds shared across all pairs that use this template.
    1. Enter a Name and Description for the profile.
    2. For HA Mode, choose Active-Passive or Active-Active.
    3. For Active-Passive, you can configure Election Options, Synchronize. For Active-Active, you can configure Election Options, Synchronize, Packet Forwarding, and Virtual Address.
    4. Select the SSH HA Profile you created.
      • (Optional) Modify the link status of the HA ports on the passive firewall.
        The passive link state is shutdown by default. After you enable HA, the link state for the HA ports on the active firewall will be green and those on the passive firewall will be down and display as red.
        Setting the link state to Auto reduces the amount of time it takes for the passive firewall to take over when a failover occurs and allows you to monitor the link state.
      • (Optional) Set the Monitor Fail Hold Down Time (min), which is the number of minutes after which a down link is retested to see if it is back up; range is 1 to 60; default is 1.
      • (PA-7500 Firewalls only) Enable HSCI to configure Device ID and HSCI VLANs.
        • (Mandatory) Configure a unique Device ID as 0 or 1 on each HA peer.
        • (Optional) Configure HSCI-A VLAN and HSCI-B VLAN to specify the VLAN tag for L2 headers. If you do not specify a value, the default VLAN tag of 2 is applied to both ports.
    5. Configure the Election Settings.
      • Select Device Priority.
      • Enable Preemptive.
        You must enable preemptive on both the active firewall and the passive firewall.
      • Enable Heartbeat Backup.
        Verify that the management port across both peers can route to each other to allow heartbeats to be transmitted between the firewalls.
        Enabling heartbeat backup prevents split-brain situations. Split brain occurs when the HA1 link goes down causing the firewall to miss heartbeats while still functioning, causing each peer to believe the other is down and attempt to start services. When the heartbeat backup link is enabled, redundant heartbeats and hello messages transmitted over the management port prevent this condition.
      • Modify the HA Timers.
        By default, the HA timer profile is set to the Recommended profile and is suited for most HA deployments. Select Aggressive to trigger failover faster, or Advanced to define custom values.
    6. In the Synchronization tab, verify that Enable Session Synchronization is enabled.
      • Enable session synchronization so that the secondary device has the session in its dataplane, which allows the firewall to match packets to the synchronized session and quickly forward packets. Without session synchronization, the firewall must create the session again, which introduces latency and could drop connections.
      • For Transport, select the method your deployment requires.
        • Layer2 transport via Ethernet—Use when the firewalls are connected back-to-back or through a switch (EtherType 0x7262).
        • Layer3 transport via IP protocol 99—Use when Layer 3 transport is required (IP protocol number 99).
        • Layer4 transport via UDP/29281—Use to verify the integrity of session sync messages using a UDP checksum calculated on the entire packet (UDP port 29281).
      • (Best Practices) Enable and configure HA2 Keep-alive to monitor the health of the HA2 data link between the HA peers.
        • For Keep-alive Action, choose Log Only for active/passive deployments. This logs HA2 interface failures as critical events without disabling the passive peer, which is not forwarding traffic.
        • For Keep-alive Threshold (ms), specify the duration after which the keep-alive action is triggered. Range is 5,000 to 60,000; default is 10,000.
    7. Configure Packet Forwarding behavior during failover. This is displayed only if you select Active-Active.
      • Enable QoS Sync to synchronize interface QoS Configuration between peers.
      • Enable VR/LR Sync to synchronize Virtual Router/Logical Router configuration.
      • Enter Tentative Hold Time (ms) in seconds to stay in tentative state following a link/path monitor recovery or before moving to an Active state (default: 60 seconds).
      • Select the Device ID for session handling.
      • Choose how sessions are assigned. Primary Device or First Packet.
    8. Set up Virtual Addresses for the HA pair. Virtual addresses are used for failover scenarios where you want a consistent IP address that clients can use regardless of which device is active. This is displayed only if you select Active-Active.
      Click +Add Virtual Address to configure the following:
      • Select the Interface where the virtual address will be assigned.
      • Configure the IPv4 and IPv6 address.
    9. Click Save.
  6. Select HA SSH Profiles and click Add HA SSH Profile.
    1. Enter a Name for the HA SSH profile.
    2. (Optional) Configure the SSH Algorithm Settings by adding one or more Cipher, MAC, and KEX algorithms, and selecting the Host Key algorithm.
    3. (Optional) Configure Session Information by specifying the maximum Data (MB) transferred, Interval (sec), and number of Packets per session before rekeying.
    4. Click Save.
  7. Select HA Monitoring Profiles and click Add Monitoring Profile.
    The HA Monitoring Profile defines the link and path monitoring conditions that trigger failover across all pairs that reference this template.
    1. Enter a Name and optional Description for the profile.
    2. Enable Path Monitoring, Link Monitoring, or both to define the conditions that trigger failover for this HA pair.
    3. If you enabled Path Monitoring, configure the Path Monitoring Settings.
      • For Failure Condition, choose All Path Groups to trigger failover only when all configured path groups fail, or Any Path Group to trigger failover when any single path group fails.
      • Click + Path Group to add a path group to monitor.
        • Enter a Name for the path group.
        • Specify the Monitoring Target.
        • Configure any additional monitoring parameters as needed.
        • Save to add the path group.
        • Repeat the above step to add additional path groups as needed.
    4. If you enabled Link Monitoring, configure the Link Monitoring Settings.
      • Click + Link Group. This shows all the interface variables in the folder.
      • For Link Group Failure Condition, choose All Link Groups to trigger failover only when all configured link groups fail, or Any Link Group to trigger failover when any single link group fails.
    5. Click Save.
  8. Select HA Templates and click Add HA Template.
    An HA template combines the three profiles into a single reusable object that you can reference in onboarding rules and HA setups.
    1. Enter a Name for the template.
    2. Select the HA Group Profile, HA Interface Profile, and HA Monitoring Profile you created.
    3. Click Save.
  9. Select HA Setups and click Add HA Setup.
    1. Enter a Name for the HA setup.
    2. (Optional) Select Enabled to activate the HA setup immediately after saving.
    3. For HA Template, select the HA template that defines the interface, group, and monitoring profiles for this HA pair.
    4. Configure the Device Configuration.
      • For Primary Device/Device 0, select the firewall to act as the primary active HA peer.
      • For Secondary Device/Device 1, select the firewall to act as the secondary passive HA peer. The model and OS version must match the primary device.
      • Enter a Group ID between 1 and 63. The Group ID uniquely identifies each HA pair on your network. If you have multiple HA pairs on the same broadcast domain, assign a unique Group ID to each pair.
    5. Click Save.
  10. Push Config to push your configuration changes.

Bulk Create HA Pairs

Create multiple HA pairs at once using bulk configuration. This allows you to quickly set up multiple firewall pairs with HA templates without configuring each pair individually.
  1. Select ConfigurationNGFW and Prisma Access and select the specific Configuration Scope.
  2. Select Network & DeviceHA Setup.
  3. Click Bulk Create.
  4. In the HA Bulk Configuration dialog, select the HA Template to apply to all pairs.
  5. Click + to add Device Pairs.
  6. Enter a Name for the HA pair.
  7. Click Enabled to enable the HA pair.
  8. Select the Primary Device from the list of available devices in the selected firewall folder. Once you select the primary device, the secondary device list will show matching devices.
  9. Select the Secondary Device from the filtered list.
  10. Select the Group ID.
  11. Repeat Step 5 through Step 1o to add additional device pairs.
  12. Click Save.