Prepare the Satellite to Join the LSVPN

1. Configure a Layer 3 Interface.

   This is the physical interface that the satellite will use to connect to the portal and the gateway. This interface must be in a zone that allows access outside of the local trust network. As a best practice, create a dedicated zone for VPN connections for visibility and control over traffic destined for the corporate gateways.
2. Configure the logical tunnel interface for the tunnel to use to establish VPN tunnels with the GlobalProtect gateways.

   IP addresses aren’t required on the tunnel interface unless you plan to use dynamic routing. However, assigning an IP address to the tunnel interface can be useful for troubleshooting connectivity issues.

   1. Select NetworkInterfacesTunnel and click Add.
   2. In the Interface Name field, specify a numeric suffix, such as .2.
   3. On the Config tab, expand the Security Zone drop-down and select an existing zone or create a separate zone for VPN tunnel traffic by clicking New Zone and defining a Name for the new zone (for example lsvpnsat).
   4. In the Virtual Router drop-down, select default.
   5. (Optional) To assign an IP address to the tunnel interface:

      • For an IPv4 address, select IPv4 and Add the IP address and network mask to assign to the interface, for example 203.0.11.100/24.
      • For an IPv6 address, select IPv6, Enable IPv6 on the interface, and Add the IP address and network mask to assign to the interface, for example 2001:1890:12f2:11::10.1.8.160/80.
   6. To save the interface configuration, click OK.
3. If you generated the portal server certificate using a root CA that isn’t trusted by the satellites (for example, if you used self-signed certificates), import the root CA certificate used to issue the portal server certificate.

   The root CA certificate is required to enable the satellite to establish the initial connection with the portal to obtain the LSVPN configuration.

   1. Download the CA certificate that was used to generate the portal server certificates. If you’re using self-signed certificates, export the root CA certificate from the portal as follows:

      1. Select DeviceCertificate ManagementCertificatesDevice Certificates.
      2. Select the CA certificate, and click Export.
      3. Select Base64 Encoded Certificate (PEM) from the File Format drop-down and click OK to download the certificate. (You don’t need to export the private key.)
   2. Import the root CA certificate that you exported onto each satellite as follows.

      1. Select DeviceCertificate ManagementCertificatesDevice Certificates and click Import.
      2. Enter a Certificate Name that identifies the certificate as your client CA certificate.
      3. Browse to the Certificate File that you downloaded from the CA.
      4. Select Base64 Encoded Certificate (PEM) as the File Format and then click OK.
      5. Select the certificate that you imported on the Device Certificates tab to open it.
      6. Select Trusted Root CA and then click OK.
4. Configure the IPSec tunnel configuration.

   1. Select NetworkIPSec Tunnels and click Add.
   2. On the General tab, enter a descriptive Name for the IPSec configuration.
   3. Select the Tunnel Interface that you created for the satellite.
   4. Select GlobalProtect Satellite as the Type.
   5. Enter the IP address or FQDN of the portal as the Portal Address.
   6. Select the Layer 3 Interface you configured for the satellite.
   7. Select the IP Address to use on the selected interface. You can select an IPv4 address, an IPv6 address, or both. Specify if you want IPv6 preferred for portal registration.
5. (Optional) Configure the satellite to publish local routes to the gateway.

   Pushing routes to the gateway enables traffic to the subnets local to the satellite via the gateway. However, you must also configure the gateway to accept the routes as detailed in Configure GlobalProtect Gateways for LSVPN.

   1. To enable the satellite to push routes to the gateway, on the Advanced tab select Publish all static and connected routes to Gateway.

      If you select this check box, the firewall will forward all static and connected routes from the satellite to the gateway. However, to prevent the creation of routing loops, the firewall will apply some route filters, such as the following:

      • Default routes
      • Routes within a virtual router other than the virtual router associated with the tunnel interface
      • Routes using the tunnel interface
      • Routes using the physical interface associated with the tunnel interface
   2. (Optional) If you only want to push routes for specific subnets rather than all routes, click Add in the Subnet section and specify which subnet routes to publish.
6. Save the satellite configuration.

   1. Click OK to save the IPSec tunnel settings.
   2. Click Commit.
7. If required, provide the credentials to allow the satellite to authenticate to the portal.

   To authenticate to the portal for the first time, the satellite administrator must provide the username and password associated with the satellite admin account in the local database.

   1. Select NetworkIPSec Tunnels and click the Gateway Info link in the Status column of the tunnel configuration you created for the LSVPN.
   2. Click the enter credentials link in the Portal Status field and provide the username and password to authenticate the satellite to the portal.

      After the portal successfully authenticates to the portal, it will receive its signed certificate and configuration, which it will use to connect to the gateway(s). You should see that the tunnel is established and the Status is changed to Active.