Configure an Interface as a DHCP Server
The prerequisites for this task are:
- Configure a Layer 3 Ethernet or Layer 3 VLAN interface.
- Assign the interface to a virtual router and a zone.
- Determine a valid pool of IP addresses from your network plan that you can designate to be assigned by your DHCP server to clients.
- Collect the DHCP options, values, and Vendor Class Identifiers you plan to configure.
You can configure a combined total of 500 DHCP servers (IPv4) and DHCP relay agents (IPv4 and IPv6) on a firewall.
Perform the following task to configure an interface on the firewall to act as a DHCP server.
- Select an interface to be a DHCP Server.
- Selectand clickNetworkDHCPDHCP ServerAdd.
- Enter anInterfacename or select one from the drop-down.
- ForMode, selectenabledorautomode. Auto mode enables the server and disables it if another DHCP server is detected on the network. Thedisabledsetting disables the server.
- (Optional) SelectPing IP when allocating new IPif you want the server to ping the IP address before it assigns that address to its client.If the ping receives a response, that means a different device already has that address, so it is not available. The server assigns the next address from the pool instead. This behavior is similar toOptimistic Duplicate Address Detection (DAD) for IPv6, RFC 4429.After you set options and return to the DHCP server tab, theProbe IPcolumn for the interface indicates ifPing IP when allocating new IPwas selected.
- Configure the predefined DHCP Options that the server sends to its clients.
- In the Options section, select aLeasetype:
- Unlimitedcauses the server to dynamically choose IP addresses from theIP Poolsand assign them permanently to clients.
- Timeoutdetermines how long the lease will last. Enter the number ofDaysandHours, and optionally the number ofMinutes.
Specifying an inheritance source allows the firewall to quickly add DHCP options from the upstream server received by the DHCP client. It also keeps the client options updated if the source changes an option. For example, if the source replaces its NTP server (which had been identified as thePrimary NTPserver), the client will automatically inherit the new address as itsPrimary NTPserver.When inheriting DHCP option(s) that contain multiple IP addresses, the firewall uses only the first IP address contained in the option to conserve cache memory. If you require multiple IP addresses for a single option, configure the DHCP options directly on that firewall rather than configure inheritance.
- Inheritance Source—LeaveNoneor select a source DHCP client interface or PPPoE client interface to propagate various server settings into the DHCP server. If you specify anInheritance Source, select one or more options below that you wantinheritedfrom this source.
For the following fields, click the down arrow and selectNone, orinherited, or enter a remote server’s IP address that your DHCP server will send to clients for accessing that service. If you selectinherited,the DHCP server inherits the values from the source DHCP client specified as theInheritance Source.
- Check inheritance source status—If you selected anInheritance Source, clicking this link opens theDynamic IP Interface Statuswindow, which displays the options that were inherited from the DHCP client.
- Gateway—IP address of the network gateway (an interface on the firewall) that is used to reach any device not on the same LAN as this DHCP server.
- Subnet Mask—Network mask used with the addresses in theIP Pools.
- Primary DNS, Secondary DNS—IP address of the preferred and alternate Domain Name System (DNS) servers.
- Primary WINS, Secondary WINS—IP address of the preferred and alternate Windows Internet Naming Service (WINS) servers.
- Primary NIS, Secondary NIS—IP address of the preferred and alternate Network Information Service (NIS) servers.
- Primary NTP, Secondary NTP—IP address of the available Network Time Protocol servers.
- POP3 Server—IP address of a Post Office Protocol (POP3) server.
- SMTP Server—IP address of a Simple Mail Transfer Protocol (SMTP) server.
- DNS Suffix—Suffix for the client to use locally when an unqualified hostname is entered that it cannot resolve.
- (Optional) Configure a vendor-specific or custom DHCP option that the DHCP server sends to its clients.
- In the Custom DHCP Options section, clickAddand enter a descriptiveNameto identify the DHCP option.
- Enter theOption Codeyou want to configure the server to offer (range is 1-254). (See RFC 2132 for option codes.)
- If theOption Codeis43, theVendor Class Identifierfield appears. Enter a VCI, which is a string or hexadecimal value (with 0x prefix) used as a match against a value that comes from the client Request containing option 60. The server looks up the incoming VCI in its table, finds it, and returns Option 43 and the corresponding option value.
- Inherit from DHCP server inheritance source—Select it only if you specified anInheritance Sourcefor the DHCP Server predefined options and you want the vendor-specific and custom options also to beinheritedfrom this source.
- Check inheritance source status—If you selected anInheritance Source, clicking this link opensDynamic IP Interface Status, which displays the options that were inherited from the DHCP client.
- If you did not selectInherit from DHCP server inheritance source, select anOption Type:IP Address,ASCII, orHexadecimal. Hexadecimal values must start with the 0x prefix.
- Enter theOption Valueyou want the DHCP server to offer for thatOption Code. You can enter multiple values on separate lines.
- (Optional) Add another vendor-specific or custom DHCP option.
- Repeat Step 3 to enter another custom DHCP Option.
- You can enter multiple option values for anOption Codewith the sameOption Name, but all values for anOption Codemust be the same type (IP Address,ASCII, orHexadecimal). If one type is inherited or entered and a different type is entered for the sameOption Codeand the sameOption Name, the second type will overwrite the first type.When entering multiple values for an option, enter the values in the order of preference, or else move the Custom DHCP Options to achieve the preferred order in the list. Select an option and clickMove UporMove Down.
- You can enter anOption Codemore than once by using a differentOption Name. In this case, theOption Typefor the Option Code can differ among the multiple option names.
- Identify the stateful pool of IP addresses from which the DHCP server chooses an address and assigns it to a DHCP client.If you are not the network administrator for your network, ask the network administrator for a valid pool of IP addresses from the network plan that can be designated to be assigned by your DHCP server.
- In theIP Poolsfield, clickAddand enter the range of IP addresses from which this server assigns an address to a client. Enter an IP subnet and subnet mask (for example, 192.168.1.0/24) or a range of IP addresses (for example, 192.168.1.10-192.168.1.20).
- An IP Pool or aReserved Addressis mandatory for dynamic IP address assignment.
- An IP Pool is optional for static IP address assignment as long as the static IP addresses that you assign fall into the subnet that the firewall interface services.
- (Optional) Repeat Step 1 to specify another IP address pool.
- (Optional) Specify an IP address from the IP pools that will not be assigned dynamically. If you also specify aMAC Address, theReserved Addressis assigned to that device when the device requests an IP address through DHCP.
- In theReserved Addressfield, clickAdd.
- Enter an IP address from theIP Pools(formatx.x.x.x) that you do not want to be assigned dynamically by the DHCP server.
- (Optional) Specify theMAC Address(formatxx:xx:xx:xx:xx:xx) of the device to which you want to permanently assign the IP address specified in Step 2.
- Save the configuration.ClickOKandCommitthe change.
Network > DHCP
Network > DHCP Dynamic Host Configuration Protocol (DHCP) is a standardized protocol that provides TCP/IP and link-layer configuration parameters and network addresses to dynamically configured ...
Configure an Interface as a DHCP Client
Configure an Interface as a DHCP Client Before configuring a firewall interface as a DHCP Client , make sure you have configured a Layer 3 ...
Configure the Management Interface as a DHCP Client
Configure the Management Interface as a DHCP Client The management interface on the firewall supports DHCP client for IPv4, which allows the management interface to ...
Configure an Interface as a DHCP Relay Agent
Configure an Interface as a DHCP Relay Agent To enable a firewall interface to transmit DHCP messages between clients and servers , you must configure ...
View DHCP Server Information
View DHCP Server Information To view DHCP pool statistics, IP addresses the DHCP server has assigned, the corresponding MAC address, state and duration of the ...
Network > GlobalProtect > Gateways
Network > GlobalProtect > Gateways Select Network > GlobalProtect > Gateways to configure a GlobalProtect gateway. A gateway can provide VPN connections for GlobalProtect agents ...
DHCP Overview DHCP is a standardized protocol defined in RFC 2131 , Dynamic Host Configuration Protocol . DHCP has two main purposes: to provide TCP/IP ...
DHCP This section describes Dynamic Host Configuration Protocol (DHCP) and the tasks required to configure an interface on a Palo Alto Networks firewall to act ...
Firewall as a DHCP Server and Client
Firewall as a DHCP Server and Client The firewall can function as a DHCP server and as a DHCP client. Dynamic Host Configuration Protocol , ...