Device > User Identification > Captive Portal Settings
Edit ( ) the Captive Portal Settings to configure the firewall to authenticate users whose traffic matches an Authentication policy rule.
If Captive Portal will use an SSL/TLS Service profile (Device > Certificate Management > SSL/TLS Service Profile), authentication profile (Device > Authentication Profile), or Certificate Profile (Device > Certificate Management > Certificate Profile), then configure the profile before you begin. The complete procedure to configure Captive Portal requires additional tasks besides configuring these profiles.
Enable Captive Portalto enforce Authentication policy (see Policies > Authentication).
Enable Captive Portal
Select this option to enable Captive Portal.
Idle Timer (min)
Enter the user time-to-live (TTL) value in minutes for a Captive Portal session (range is 1 to 1,440; default is 15). This timer resets every time there is activity from a Captive Portal user. If idle time for a user exceeds the
Idle Timervalue, PAN-OS removes the Captive Portal user mapping and the user must log in again.
This is the maximum TTL in minutes, which is the maximum time that any Captive Portal session can remain mapped (range is 1 to 1,440; default is 60). After this duration elapses, PAN-OS removes the mapping and users must re-authenticate even if the session is active. This timer prevents stale mappings and overrides the
You should always set the expiration
Timerhigher than the
SSL/TLS Service Profile
To specify a firewall server certificate and the allowed protocols for securing redirect requests, select an SSL/TLS service profile (Device > Certificate Management > SSL/TLS Service Profile). If you select
None, the firewall uses its local default certificate for SSL/TLS connections.
To transparently redirect users without displaying certificate errors, assign a profile associated with a certificate that matches the IP address of the interface to which you are redirecting web requests.
You can select an authentication profile (Device > Authentication Profile) to authenticate users when their traffic matches an Authentication policy rule (Policies > Authentication). However, the authentication profile you select in the Captive Portal Settings applies only to rules that reference one of the default authentication enforcement objects (Objects > Authentication). This is typically the case right after an upgrade to PAN-OS 8.0 because all Authentication rules initially reference the default objects. For rules that reference custom authentication enforcement objects, select the authentication profile when you create the object.
GlobalProtect Network Port for Inbound Authentication Prompts (UDP)
Specify the port that GlobalProtect™ uses to receive inbound authentication prompts from multi-factor (MFA) gateways. (range is 1 to 65,536; default is 4,501). To support multi-factor authentication, a GlobalProtect client must receive and acknowledge UDP prompts that are inbound from the MFA gateway. When a GlobalProtect client receives a UDP message on the specified network port and the UDP message comes from a trusted firewall or gateway, GlobalProtect displays the authentication message (see Customize the GlobalProtect Agent ).
Select how the firewall captures web requests for authentication:
Redirectmode is required if Captive Portal uses Kerberos SSO or NTLM authentication because the browser provides credentials only to trusted sites.
Redirectmode is also required if Captive Portal uses multi-factor authentication (MFA).
Redirect mode only)
Redirect mode only)
Specify the intranet hostname that resolves to the IP address of the Layer 3 interface to which the firewall redirects web requests.
You can select a Certificate Profile (Device > Certificate Management > Certificate Profile) to authenticate users when their traffic matches any Authentication policy rule (Policies > Authentication).
For this authentication type, Captive Portal prompts the client browser of the user to present a client certificate. Therefore, you must deploy client certificates to each user system. Furthermore, on the firewall, you must install the certificate authority (CA) certificate that issued the client certificates and assign the CA certificate to the Certificate Profile. This is the only authentication method that enables
Transparentauthentication for Mac OS and Linux clients.
When you configure Captive Portal for NT LAN Manager (NTLM) authentication , the firewall uses an encrypted challenge-response mechanism to transparently obtain user credentials from the browser without prompting the user.
To invoke NTLM authentication, Authentication policy rules must specify an
Authentication Enforcementobject with the
Authentication Methodset to
default-browser-challenge(Objects > Authentication). If the object specifies an
Authentication Profilewith Kerberos single sign-on (SSO) enabled, the firewall first attempts Kerberos authentication before falling back to NTLM. If the browser cannot perform NTLM or if NTLM authentication fails, the firewall falls back to
By default, Internet Explorer supports NTLM. You can configure Firefox and Chrome to use it, as well, but you cannot use NTLM to authenticate non-Windows clients.
Choose Kerberos SSO transparent authentication over NTLM authentication when configuring Captive Portal. Kerberos is a stronger, more robust authentication method than NTLM and it does not require the firewall to have an administrative account to join the domain.
These options apply only to the Windows-based User-ID agents. When using the PAN-OS integrated User-ID agent, the firewall must be able to successfully resolve the DNS name of your domain controller to join the domain. You can then Enable NTLM Authentication in the PAN-OS integrated User-ID agent setup and provide the credentials for the firewall to join the domain. NTLM is available only for Windows Server version 2003 and earlier versions.
To configure NTLM for use with Windows-based User-ID agents, define the following:
Recommended For You
Recommended videos not found.