Identify Sessions That Use an Excessive Percentage of the
When a firewall exhibits signs of resource depletion, it might be experiencing an attack that is sending an overwhelming number of packets. In such events, the firewall starts buffering inbound packets. You can quickly identify the sessions that are using an excessive percentage of the packet buffer and mitigate their impact by discarding them.
Perform the following task on any hardware-based firewall model (not a VM-Series firewall) to identify, for each slot and dataplane, the packet buffer percentage used, the top five sessions using more than two percent of the packet buffer, and the source IP addresses associated with those sessions. Having that information allows you to take appropriate action.
- View firewall resource usage, top sessions, and session details. Execute the following operational command in the CLI (sample output from the command follows):admin@PA-7050>show running resource-monitor ingress-backlogs-- SLOT:s1, DP:dp1 -- USAGE - ATOMIC: 92% TOTAL: 93% TOP SESSIONS:SESS-ID PCT GRP-ID COUNT 6 92% 1 156 7 1732 SESSION DETAILS SESS-ID PROTO SZONESRC SPORT DST DPORT IGR-IF EGR-IF APP 6 6 trust 192.168.2.35 55653 10.1.8.89 80 ethernet1/21 ethernet1/22 undecidedThe command displays a maximum of the top five sessions that each use 2% or more of the packet buffer.The sample output above indicates that Session 6 is using 92% of the packet buffer with TCP packets (protocol 6) coming from source IP address 192.168.2.35.
To restrict the display output:On a PA-7000 Series model only, you can limit output to a slot, a dataplane, or both. For example:admin@PA-7050>show running resource-monitor ingress-backlogs slot s1admin@PA-7050>show running resource-monitor ingress-backlogs slot s1 dp dp1On PA-5200 Series and PA-7000 Series models only, you can limit output to a dataplane. For example:admin@PA-5260>show running resource-monitor ingress-backlogs dp dp1
- SESS-ID—Indicates the global session ID that is used in all othershow sessioncommands. The global session ID is unique within the firewall.
- GRP-ID—Indicates an internal stage of processing packets.
- COUNT—Indicates how many packets are in that GRP-ID for that session.
- APP—Indicates the App-ID extracted from the Session information, which can help you determine whether the traffic is legitimate. For example, if packets use a common TCP or UDP port but the CLI output indicates an APP ofundecided, the packets are possibly attack traffic. The APP isundecidedwhen Application IP Decoders cannot get enough information to determine the application. An APP ofunknownindicates that Application IP Decoders cannot determine the application; a session ofunknownAPP that uses a high percentage of the packet buffer is also suspicious.
- Use the command output to determine whether the source at the source IP address using a high percentage of the packet buffer is sending legitimate or attack traffic.In the sample output above, a single-session attack is likely occurring. A single session (Session ID 6) is using 92% of the packet buffer for Slot 1, DP 1, and the application at that point isundecided.
To see whether a session is offloaded or not, use theshow session idoperational command in the CLI as shown in the following example. The<session-id>layer7processingvalue indicatescompletedfor sessions offloaded orenabledfor sessions not offloaded.
- If you determine a single user is sending an attack and the traffic is not offloaded, you can End a Single Session DoS Attack. At a minimum, you can Configure DoS Protection Against Flooding of New Sessions.
- On a hardware model that has a field-programmable gate array (FPGA), the firewall offloads traffic to the FPGA when possible to increase performance. If the traffic is offloaded to hardware, clearing the session does not help because then it is the software that must handle the barrage of packets. You should instead Discard a Session Without a Commit.
Recommended For You
Recommended videos not found.