Add a ZTP Firewall to Panorama
Table of Contents
11.1 & Later
Expand all | Collapse all
-
- Determine Panorama Log Storage Requirements
-
- Setup Prerequisites for the Panorama Virtual Appliance
- Perform Initial Configuration of the Panorama Virtual Appliance
- Set Up The Panorama Virtual Appliance as a Log Collector
- Set Up the Panorama Virtual Appliance with Local Log Collector
- Set up a Panorama Virtual Appliance in Panorama Mode
- Set up a Panorama Virtual Appliance in Management Only Mode
-
- Preserve Existing Logs When Adding Storage on Panorama Virtual Appliance in Legacy Mode
- Add a Virtual Disk to Panorama on an ESXi Server
- Add a Virtual Disk to Panorama on vCloud Air
- Add a Virtual Disk to Panorama on Alibaba Cloud
- Add a Virtual Disk to Panorama on AWS
- Add a Virtual Disk to Panorama on Azure
- Add a Virtual Disk to Panorama on Google Cloud Platform
- Add a Virtual Disk to Panorama on KVM
- Add a Virtual Disk to Panorama on Hyper-V
- Add a Virtual Disk to Panorama on Oracle Cloud Infrastructure (OCI)
- Mount the Panorama ESXi Server to an NFS Datastore
-
- Increase CPUs and Memory for Panorama on an ESXi Server
- Increase CPUs and Memory for Panorama on vCloud Air
- Increase CPUs and Memory for Panorama on Alibaba Cloud
- Increase CPUs and Memory for Panorama on AWS
- Increase CPUs and Memory for Panorama on Azure
- Increase CPUs and Memory for Panorama on Google Cloud Platform
- Increase CPUs and Memory for Panorama on KVM
- Increase CPUs and Memory for Panorama on Hyper-V
- Increase the CPUs and Memory for Panorama on Oracle Cloud Infrastructure (OCI)
- Complete the Panorama Virtual Appliance Setup
-
- Convert Your Evaluation Panorama to a Production Panorama with Local Log Collector
- Convert Your Evaluation Panorama to a Production Panorama without Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing with Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing without Local Log Collector
- Convert Your Production Panorama to an ELA Panorama
-
- Register Panorama
- Activate a Panorama Support License
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is Internet-connected
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is not Internet-connected
- Activate/Retrieve a Firewall Management License on the M-Series Appliance
- Install the Panorama Device Certificate
- Install the Device Certificate for a Dedicated Log Collector
-
- Migrate from a Panorama Virtual Appliance to an M-Series Appliance
- Migrate a Panorama Virtual Appliance to a Different Hypervisor
- Migrate from an M-Series Appliance to a Panorama Virtual Appliance
- Migrate from an M-500 Appliance to an M-700 Appliance
- Migrate from an M-600 Appliance to an M-700 Appliance
- Migrate from an M-100 Appliance to an M-500 Appliance
- Migrate from an M-100 or M-500 Appliance to an M-200 or M-600 Appliance
-
- Configure an Admin Role Profile
- Configure an Admin Role Profile for Selective Push to Managed Firewalls
- Configure an Access Domain
-
- Configure a Panorama Administrator Account
- Configure Local or External Authentication for Panorama Administrators
- Configure a Panorama Administrator with Certificate-Based Authentication for the Web Interface
- Configure an Administrator with SSH Key-Based Authentication for the CLI
- Configure RADIUS Authentication for Panorama Administrators
- Configure TACACS+ Authentication for Panorama Administrators
- Configure SAML Authentication for Panorama Administrators
- Enable SCP Uploads for an Administrator
- Configure Tracking of Administrator Activity
-
- Add a Firewall as a Managed Device
- Change Between Panorama Management and Cloud Management
-
- Add a Device Group
- Create a Device Group Hierarchy
- Create Objects for Use in Shared or Device Group Policy
- Revert to Inherited Object Values
- Manage Unused Shared Objects
- Manage Precedence of Inherited Objects
- Move or Clone a Policy Rule or Object to a Different Device Group
- Push a Policy Rule to a Subset of Firewalls
- Device Group Push to a Multi-VSYS Firewall
- Manage the Rule Hierarchy
- Manage the Master Key from Panorama
- Schedule a Configuration Push to Managed Firewalls
- Redistribute Data to Managed Firewalls
-
- Plan the Transition to Panorama Management
- Migrate a Firewall to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall to Panorama Management and Push a New Configuration
- Migrate a Firewall HA Pair to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall HA Pair to Panorama Management and Push a New Configuration
- Load a Partial Firewall Configuration into Panorama
- Localize a Panorama Pushed Configuration on a Managed Firewall
-
- Configure a Managed Collector
- Monitor Managed Collector Health Status
- Configure Log Forwarding to Panorama
- Configure Syslog Forwarding to External Destinations
- Forward Logs to Strata Logging Service
- Verify Log Forwarding to Panorama
- Modify Log Forwarding and Buffering Defaults
- Configure Log Forwarding from Panorama to External Destinations
-
- Add Standalone WildFire Appliances to Manage with Panorama
- Remove a WildFire Appliance from Panorama Management
-
-
- Configure a Cluster and Add Nodes on Panorama
- Configure General Cluster Settings on Panorama
- Remove a Cluster from Panorama Management
- Configure Appliance-to-Appliance Encryption Using Predefined Certificates Centrally on Panorama
- Configure Appliance-to-Appliance Encryption Using Custom Certificates Centrally on Panorama
- View WildFire Cluster Status Using Panorama
-
-
- Preview, Validate, or Commit Configuration Changes
- Commit Selective Configuration Changes for Managed Devices
- Push Selective Configuration Changes to Managed Devices
- Enable Automated Commit Recovery
- Compare Changes in Panorama Configurations
- Manage Locks for Restricting Configuration Changes
- Add Custom Logos to Panorama
- Use the Panorama Task Manager
- Reboot or Shut Down Panorama
- Configure Panorama Password Profiles and Complexity
-
-
- Verify Panorama Port Usage
- Resolve Zero Log Storage for a Collector Group
- Replace a Failed Disk on an M-Series Appliance
- Replace the Virtual Disk on an ESXi Server
- Replace the Virtual Disk on vCloud Air
- Migrate Logs to a New M-Series Appliance in Log Collector Mode
- Migrate Logs to a New M-Series Appliance in Panorama Mode
- Migrate Logs to a New M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Logs to the Same M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Log Collectors after Failure/RMA of Non-HA Panorama
- Regenerate Metadata for M-Series Appliance RAID Pairs
- View Log Query Jobs
- Troubleshoot Registration or Serial Number Errors
- Troubleshoot Reporting Errors
- Troubleshoot Device Management License Errors
- Troubleshoot Automatically Reverted Firewall Configurations
- View Task Success or Failure Status
- Generate a Stats Dump File for a Managed Firewall
- Recover Managed Device Connectivity to Panorama
- Restore an Expired Device Certificate
Add a ZTP Firewall to Panorama
Add a ZTP firewall to be managed by the Panorama management server.
Where Can I Use This? | What Do I Need? |
---|---|
|
|
Log in to the web interface of the Panorama™ management server as a Superuser, Panorama admin,
or as the ZTP installer admin to add a ZTP firewall to
Panorama. To add the ZTP firewall, you must enter the firewall serial number and claim key
provided by Palo Alto Networks and then register the firewall with the ZTP service. Registering
the firewall claims the firewall as an asset in your account in the Customer Support Portal and
allows the ZTP service to associate the firewall with the Panorama.
Before you can successfully add a ZTP firewall to Panorama, you must ensure that a Dynamic
Host Configuration Protocol (DHCP) server is deployed on the network. A DHCP server is required
to successfully onboard a ZTP firewall to Panorama. The ZTP firewall is unable to connect to the
Palo Alto Networks ZTP service to facilitate onboarding without a DHCP server.
Do not power on the ZTP firewall until after you finish all the required installation and
setup procedures.
Do not power on the ZTP firewall until after you finish all the required installation and
setup procedures. This causes ZTP onboarding to fail and you must reset the
firewall to factory default settings to restart the ZTP onboarding process.
Migrating a firewall added to Panorama management using ZTP from one
Panorama to another is not supported.
Firewalls onboarded to Panorama management using ZTP do not support high availability (HA)
configuration.
You must disable ZTP on your firewalls to configure them in an HA configuration.
After disabling ZTP, add your firewalls as managed devices and set up your
firewalls in an active/passive or active/active HA configuration.
While adding ZTP firewalls to Panorama, do not perform any commits on the ZTP firewall before
you verify that the firewall is successfully added to Panorama. Performing a local commit on
the ZTP firewall disables ZTP functionality and results in the failure to successfully add the
firewall to Panorama.
11.1
Add a Zero Touch Provisioning (ZTP) firewall to be managed by the Panorama management
server running PAN-OS 11.1.
- Add a ZTP firewall to Panorama.You must connect the ZTP firewall to the internet using the Eth1/1 interface to successfully register the ZTP firewall with the CSP and push the policy and network configurations.
- SelectFirewall RegistrationandAdda new ZTP firewall.
- Enter theSerial Numberof the ZTP firewall.
- Enter theClaim Keyfor the ZTP firewall provided by Palo Alto Networks.The eight digit numeric claim key is printed on a physical label attached to the back of the ZTP firewall you received from Palo Alto Networks.
- ClickOKto save your configuration changes.
- Select the newly added ZTP firewall andRegisterthe firewall.When prompted, clickYesto confirm registering the ZTP firewall.
- Verify the firewall successfully registered with the CSP.The firewall must successfully register with the CSP to successfully obtain device certificate.
- SelectRegistration Statusand verify that the ZTP firewall successfully registered with the CSP.
- Log in to the Panorama Web Interface using admin credentials.
- Selectand verify that the ZTP firewall is successfully added as a managed firewall.PanoramaManaged DevicesSummaryThe ZTP firewall is listed but has aDisconnectedDevice State.Ensure that theTo SW Versioncolumn is configured to the correct PAN-OS version so that the firewall does not upgrade or downgrade unintentionally. ZTP functionality is supported only for PAN-OS 10.0.1 and later releases. Additionally, the PAN-OS version must be the same or an earlier version of the PAN-OS version running on Panorama.For more information, see Upgrade a ZTP Firewall.
- Add the ZTP firewall to the device group and template stack that contain the required ZTP configuration.You must add the ZTP firewall to a device group and template stack for your firewalls to display asConnectedto push policy and network configurations.You must keep the ZTP firewall in the ZTP device group and template stack that the ZTP template is associated with. This is required for the firewall to maintain connectivity with Panorama and prevent any unintended configuration reverts on the firewall.
- Log in to the Panorama Web Interface using admin credentials.
- Select.PanoramaManaged DevicesSummary
- Select the ZTP firewalls you added and registered in the previous step andReassociate.
- Select the ZTPDevice GroupandTemplate Stack.
- Check (enable)Auto Push on 1st Connectto automatically push the device group and template stack configurations when the ZTP firewall successfully connects to Panorama for the first time.
- (Optional) Specify theTo SW Versionto automatically upgrade your firewalls to a more recent PAN-OS version.Ensure that theTo SW Versioncolumn is configured to the correct PAN-OS version so that the firewall does not upgrade or downgrade unintentionally. ZTP functionality is supported only for PAN-OS 10.0.1 and later releases. Additionally, the PAN-OS version must be the same or an earlier version of the PAN-OS version running on Panorama.For more information, see Upgrade a ZTP Firewall.
- CommitandCommit to Panorama
- Power on the ZTP firewall.Wait for the ZTP firewall to finish powering on. On Panorama, selectand verify that the ZTP firewall is nowPanoramaManaged DevicesSummaryConnected.
- Complete setting up the newly onboarded firewall.
- Install the latest dynamic content updates on the managed firewall.
- SelectandPanoramaDevice DeploymentDynamic UpdatesCheck Nowfor the latest updates
- Downloadthe latest dynamic content release version.
- Installand select the newly added firewalls.ClickOKwhen prompted.
- (Optional) Upgrade the managed firewall as needed.
11.2 and Later
Add a Zero Touch Provisioning (ZTP) firewall to be managed by the Panorama management
server running PAN-OS 11.2 and later releases.
- Add a ZTP firewall to Panorama.You must connect the ZTP firewall to the internet using the Eth1/1 interface to successfully register the ZTP firewall with the CSP and push the policy and network configurations.
- SelectFirewall RegistrationandAdda new ZTP firewall.
- Enter theSerial Numberof the ZTP firewall.
- Enter theClaim Keyfor the ZTP firewall provided by Palo Alto Networks.The eight digit numeric claim key is printed on a physical label attached to the back of the ZTP firewall you received from Palo Alto Networks.
- Enter theAuth Codefor the ZTP to activate licenses on the firewall after it successfully connects to Panorama for the first time.
- ClickOKto save your configuration changes.
- Select the newly added ZTP firewall andRegisterthe firewall.When prompted, clickYesto confirm registering the ZTP firewall.
- Verify the firewall successfully registered with the CSP.The firewall must successfully register with the CSP to successfully obtain the device certificate.
- SelectRegistration Statusand verify that the ZTP firewall successfully registered with the CSP.
- Log in to the Panorama Web Interface using admin credentials.
- Selectand verify that the ZTP firewall is successfully added as a managed firewall.PanoramaManaged DevicesSummary
- Add the ZTP firewall to the device group and template stack that contain the required ZTP configuration.You must add the ZTP firewall to a device group and template stack for your firewalls to display asConnectedto push policy and network configurations.You must keep the ZTP firewall in the ZTP device group and template stack that the ZTP template is associated with. This is required for the firewall to maintain connectivity with Panorama and prevent any unintended configuration reverts on the firewall.
- Log in to the Panorama Web Interface using admin credentials.
- Select.PanoramaManaged DevicesSummary
- Select the ZTP firewalls you added and registered in the previous step andReassociate.
- Select the ZTPDevice GroupandTemplate Stack.
- Check (enable)Auto Push on 1st Connectto automatically push the device group and template stack configurations when the ZTP firewall successfully connects to Panorama for the first time.
- (Optional) Specify theTo SW Versionto automatically upgrade your firewalls to a more recent PAN-OS version.Ensure that theTo SW Versioncolumn is configured to the correct PAN-OS version so that the firewall does not upgrade or downgrade unintentionally. ZTP functionality is supported only for PAN-OS 10.0.1 and later releases. Additionally, the PAN-OS version must be the same or an earlier version of the PAN-OS version running on Panorama.For more information, see Upgrade a ZTP Firewall.
- CommitandCommit to Panorama
- Power on the ZTP firewall.Wait for the ZTP firewall to finish powering on. On Panorama, selectand verify that the ZTP firewall is nowPanoramaManaged DevicesSummaryConnected.