Add a Virtual Disk to Panorama on Hyper-V
Add a virtual logging disk to Panorama™ in Panorama or Log Collector mode on Hyper-V.
After you Install Panorama on Hyper-V, add virtual logging disks to the Panorama™ virtual appliance instance to provide storage for logs generated by managed firewalls. You can add virtual disks to a local log Collector for a Panorama virtual appliance in Panorama mode or for a Dedicated Log Collector. The Panorama virtual appliance on Hyper-V supports only 2TB logging disks and, in total, supports up to 24TB of log storage. You cannot add a logging disk smaller than 2TB or a logging disk of a size that is not evenly divisible by 2TB because the Panorama virtual appliance partitions logging disks in to 2TB partitions. For example, if you attach a 4TB logging disk, Panorama will create two 2TB partitions. However, you cannot add a 5TB logging disk because the leftover 1TB is not supported as a partition.
- Power off the Panorama virtual appliance.
- On the Hyper-V Manager, select the Panorama virtual appliance instance from the list ofVirtual Machines.
- Selectto power off the Panorama virtual appliance.ActionTurn Off
- Add the virtual logging disk. Repeat this step as many times as needed.
- Select the Panorama virtual appliance from the list ofVirtual Machines, and select.ActionSettings
- In theHardwarelist, selectIDE Controller 0.
- From theIDE Controllerdrives list, selectHard DriveandAddthe new virtual logging disk.
- Select the newHard Drivecreated underIDE Controller 0.
- UnderMedia, add aNewhard disk.
- Configure the new virtual logging disk.
- If you see the Before You Begin prompt, clickNextto begin adding the virtual logging disk
- For the Disk Format, selectVHDX. ClickNextto continue
- For the Disk Type, selectFixed SizeorDynamically Expandingbased on your needs. ClickNextto continue.
- Specify theNameandLocationfor the virtual logging disk file. ClickNextto continue.
- To configure the disk, selectCreate a new virtual hard diskand enter the disk size. ClickNextto continue.
- Review the Summary andFinishadding the virtual hard logging disk.
- Applythe new hard disk addition.
- Power on the Panorama virtual appliance.
- Select the Panorama virtual appliance instance from the list ofVirtual Machines.
- Selectto power on the Panorama virtual appliance.ActionStart
- Configure each disk.The following example uses the sdc virtual disk.
- Enter the following command to view the disks on the Panorama virtual appliance:show system disk detailsThe user will see the following response:Name : sdb State : Present Size : 2048 MB Status : Available Reason : Admin enabled Name : sdc State : Present Size : 2048 MB Status : Available Reason : Admin disabled
- Enter the following command and confirm the request when prompted for all disks with theReason : Admin disabledresponse:request system disk add sdcTherequest system disk addcommand is not available on a Panorama management server in Management Only mode because logging is not supported in this mode. If you do not see the command, Set up a Panorama Virtual Appliance in Panorama Mode to enable the logging disks. Once in Panorama mode, Log in to the Panorama CLI and continue to Step 4 to verify the disk addition.
- Enter theshow system disk detailscommand to verify the status of the disk addition. Continue to the next step when all newly added disk responses displayReason : Admin enabled.
- Make disks available for logging.
- Log in to the Panorama web interface.
- Edit a Log Collector ().PanoramaManaged Collectors
- SelectDisksandAddeach newly added disk.
- SelectandCommitCommit and PushCommit and Pushyour changes.
- Verify that the Panorama Log Storage capacity is increased.
- Log in to the Panorama web interface.
- Select the Collector Group to which the Panorama virtual appliance belongs ().PanoramaCollector Groups
- Verify that theLog Storagecapacity accurately displays the disk capacity.
Recommended For You
Recommended videos not found.