Prisma Access
Riverbed SteelConnect SD-WAN Solution Guide
Table of Contents
Riverbed SteelConnect SD-WAN Solution Guide
Where Can I Use This? | What Do I Need? |
|---|---|
|
|
To use this Solution Guide, you need a knowledge of the following software and hardware
concepts:
- SD-WAN routing principles
- SteelConnect Manager (SCM)
- SteelConnect appliances (in particular, SteelConnect gateways)
- Panorama appliance configuration tasks
- Prisma Access configuration tasks
Supported IKE and IPSec Cryptographic Profiles
Prisma Access supports standard IPSec tunnels from third-party SD-WAN edge devices
using IKE and IPSec Crypto profiles.
The following table documents the IKE/IPSec crypto settings that are supported with
Prisma Access and SteelConnect SD-WAN.
A check mark indicates that the profile or architecture type is supported; a dash (—)
indicates that it's not supported. Default and Recommended settings are noted in the
table.
Crypto Profiles | Prisma Access | SteelConnect SD-WAN | |
|---|---|---|---|
Tunnel Type | IPSec Tunnel |  | |
GRE Tunnel | — | — | |
Routing | Static Routes | | |
Dynamic Routing (BGP) | | | |
Dynamic Routing (OSPF) | — | | |
IKE Versions | IKE v1 | | |
IKE v2 | | | |
IPSec Phase 1 DH-Group | Group 1 | | |
Group 2 | | | |
Group 5 | | | |
Group 14 | | | |
Group 19 | | — | |
Group 20 | | — | |
IPSec Phase 1 Auth If you use
IKEv2 with certificate-based authentication, only SHA1 is
supported in IKE crypto profiles (Phase 1). | MD5 | | |
SHA1 | | | |
SHA256 | | | |
SHA384 | | | |
SHA512 | | | |
IPSec Phase 1 Encryption | DES | | — |
3DES | | | |
AES-128-CBC | | | |
AES-192-CBC | | | |
AES-256-CBC | | | |
IPSec Phase 1 Key Lifetime Default | | | |
IPSec Phase 1 Peer
Authentication | Pre-Shared Key | | |
Certificate | | | |
IKE Peer Identification | FQDN | | |
IP Address | | | |
User FQDN | | — | |
IKE Peer | As Static Peer | | |
As Dynamic Peer | | | |
Options | NAT Traversal | | |
Passive Mode | | — | |
Ability to Negotiate
Tunnel | Per Subnet Pair | | |
Per Pair of Hosts | | | |
Per Gateway Pair | | — | |
IPSec Phase 2 DH-Group | Group 1 | | |
Group 2 | | | |
Group 5 | | | |
Group 14 | | | |
Group 19 | | — | |
Group 20 | | — | |
No PFS | | — | |
IPSec Phase 2 Auth | MD5 | | |
SHA1 | | | |
SHA256 | | | |
SHA384 | | | |
SHA512 | | | |
None | | — | |
IPSec Phase 2 Encryption | DES | | — |
3DES | | | |
AES-128-CBC | | | |
AES-192-CBC | | | |
AES-256-CBC | | | |
AES-128-CCM | | — | |
AES-128-GCM | | — | |
AES-256-GCM | | | |
NULL | | | |
IPSec Protocol | ESP | | |
AH | | — | |
IPSec Phase 2 Key Lifetime Default | | | |
Tunnel Monitoring
Fallback | Dead Peer Detection (DPD) | | — |
ICMP | — | — | |
Bidirectional Forwarding Detection (BFD) | — | — | |
SD-WAN Architecture Type | With Regional Hub/Gateway/Data Center | NA | |
No Regional Hub/Gateway/Data Center | NA | | |
SD-WAN Deployment Architectures Supported by Riverbed
Riverbed supports the following deployment architectures for use with Prisma Access.
A dash (—) indicates that the deployment isn't supported.
Use Case | Architecture | Supported? |
|---|---|---|
Securing traffic from each branch site with 1 WAN
link (Type 1) Use an IPSec tunnel from each branch to Prisma
Access. Use a Riverbed SD-WAN appliance device at the
branch. |  | Yes |
Securing branch and HQ sites with active/backup
SD-WAN connections |  | No |
Securing branch and HQ sites with active/active
SD-WAN connections |  | No |
Securing branch and HQ sites with SD-WAN edge devices
in HA mode |  | Yes |
Securing SD-WAN deployments with Regional Hub/POP
architecture (Type 2) |  | Yes |