VMware SD-WAN by VeloCloud Solution Guide
The following sections describe how you
use the VMware SD-WAN by VeloCloud (VeloCloud) with Prisma Access:
Supported IKE and IPSec Cryptographic Profiles
The following table documents the IKE/IPSec crypto settings
that are supported with Prisma Access and VeloCloud devices.
A check mark indicates that the profile or architecture type
is supported; a dash (—) indicates that it is not supported. Default
and Recommended settings are noted in the table.
Crypto Profiles | Prisma Access | VeloCloud | |
---|---|---|---|
Tunnel Type | IPSec Tunnel | ![]() | ![]() |
GRE Tunnel | — | — | |
Routing | Static Routes | ![]() | ![]() |
Dynamic Routing (BGP) | ![]() | — | |
Dynamic Routing (OSPF) | — | — | |
IKE Versions | IKE v1 | ![]() | ![]() |
IKE v2 | ![]() | ![]() | |
IPSec Phase 1 DH-Group | Group 1 | ![]() | ![]() |
Group 2 | ![]() | ![]() | |
Group 5 | ![]() | ![]() | |
Group 14 | ![]() | ![]() | |
Group 19 | ![]() | — | |
Group 20 | ![]() | — | |
IPSec Phase 1 Auth If
you use IKEv2 with certificate-based authentication, only SHA1 is
supported in IKE crypto profiles (Phase 1). | MD5 | ![]() | ![]() |
SHA1 | ![]() | ![]() | |
SHA256 | ![]() | ![]() | |
SHA384 | ![]() | — | |
SHA512 | ![]() | — | |
IPSec Phase 1 Encryption | DES | ![]() | — |
3DES | ![]() | — | |
AES-128-CBC | ![]() | ![]() | |
AES-192-CBC | ![]() | — | |
AES-256-CBC | ![]() | ![]() | |
IPSec Phase 1 Key Lifetime Default | ![]() | ![]() | |
IPSec Phase 1 Peer Authentication | Pre-Shared Key | ![]() | ![]() |
Certificate | ![]() | — | |
IKE Peer Identification | FQDN | ![]() | ![]() |
IP Address | ![]() | — | |
User FQDN | ![]() | — | |
IKE Peer | As Static Peer | ![]() | ![]() |
As Dynamic Peer | ![]() | — | |
Options | NAT Traversal | ![]() | ![]() |
Passive Mode | ![]() | ![]() | |
Ability to Negotiate Tunnel | Per Subnet Pair | ![]() | — |
Per Pair of Hosts | ![]() | — | |
Per Gateway Pair | ![]() | — | |
IPSec Phase 2 DH-Group | Group 1 | ![]() | — |
Group 2 | ![]() | ![]() | |
Group 5 | ![]() | ![]() | |
Group 14 | ![]() | ![]() | |
Group 19 | ![]() | — | |
Group 20 | ![]() | — | |
No PFS | ![]() | — | |
IPSec Phase 2 Auth | MD5 | ![]() | ![]() |
SHA1 | ![]() | ![]() | |
SHA256 | ![]() | ![]() | |
SHA384 | ![]() | — | |
SHA512 | ![]() | — | |
None | ![]() | — | |
IPSec Phase 2 Encryption | DES | ![]() | — |
3DES | ![]() | — | |
AES-128-CBC | ![]() | ![]() | |
AES-192-CBC | ![]() | — | |
AES-256-CBC | ![]() | ![]() | |
AES-128-CCM | ![]() | — | |
AES-128-GCM | ![]() | — | |
AES-256-GCM | ![]() | — | |
NULL | ![]() | — | |
IPSec Protocol | ESP | ![]() | ![]() |
AH | ![]() | — | |
IPSec Phase 2 Key Lifetime Default | ![]() | ![]() | |
Tunnel Monitoring Fallback | Dead Peer Detection (DPD) | ![]() | ![]() |
ICMP | — | — | |
Bidirectional Forwarding Detection (BFD) | — | — | |
SD-WAN Architecture Type | With Regional Hub/Gateway/Data Center | N/A | ![]() |
No Regional Hub/Gateway/Data Center | NA | ![]() |
SD-WAN Deployment Architectures Supported by VMware SD-WAN
The VMware VeloCloud SD-WAN supports the following deployment architectures
for use with Prisma Access. a dash (—) indicates that the deployment is
not supported.
Use Case | Architecture | Supported? |
---|---|---|
Securing traffic from each branch site with
1 WAN link (Type 1) | ![]() | ![]() |
Securing branch and HQ sites with active/backup SD-WAN connections | ![]() | ![]() |
Securing branch and HQ sites with active/active SD-WAN connections | ![]() | — |
Securing branch and HQ sites with SD-WAN edge devices
with a primary and secondary tunnel | ![]() | ![]() |
Securing SD-WAN deployments with Regional Hub/POP architecture (Type
2) | ![]() | ![]() |
Most Popular
Recommended For You
Recommended Videos
Recommended videos not found.