Bandwidth Utilization
Table of Contents
Expand all | Collapse all
-
-
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Enable IoT Device Visibility in Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Prisma SD-WAN Standard VPN
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
-
- Native SASE Integration with Prisma SD-WAN
- Connect a Single Prisma SD-WAN Site to Prisma Access
- Connect Multiple Prisma SD-WAN Sites to Prisma Access
- Edit Application Policy Network Rules
- Understand Service and Data Center Groups
- Verify Standard VPN Endpoints
- Configure Standard Groups
- Assign Domains to Sites
- Prisma SD-WAN Incidents and Alerts
Bandwidth Utilization
Displays the amount of bandwidth utilized on a trail
in a CloudGenix network.
The
Bandwidth Utilization
chart
displays the amount of bandwidth utilized on a trail in a network. Use
the chart to identify WAN congestion in a network that may hinder
application performance. It is a visual representation of bandwidth
spike, total bandwidth consumed by a particular site, and the application;
if the upload is in ingress or egress direction.Move your cursor in the Bandwidth Utilization chart to get a
more granular view of the bandwidth utilization with an application
or time-stamp. Typically, the apps are listed in order of their
bandwidth utilization.
The chart displays the bandwidth consumed over time. The
1H
view
provides granular per minute data, and the 1D
picture
shows data every 5 minutes. The 1D chart data averages above 5 minutes
for each sample. If utilization sustains above 5 minutes, you can
see the corresponding peak utilization in both charts.Select
Circuits
to view and narrow down
the traffic by a circuit path such as the Internet
and Private
WAN
.The broken line indicates the configured bandwidth for the selected
circuit.