Enable BGP for Private WAN and LAN
Table of Contents
Expand all | Collapse all
-
-
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Enable IoT Device Visibility in Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Prisma SD-WAN Standard VPN
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
-
- Native SASE Integration with Prisma SD-WAN
- Connect a Single Prisma SD-WAN Site to Prisma Access
- Connect Multiple Prisma SD-WAN Sites to Prisma Access
- Edit Application Policy Network Rules
- Understand Service and Data Center Groups
- Verify Standard VPN Endpoints
- Configure Standard Groups
- Assign Domains to Sites
- Prisma SD-WAN Incidents and Alerts
Enable BGP for Private WAN and LAN
Learn more about the enable BGP for private WAN and LAN.
Enable
L3 Direct Private WAN Forwarding
to
allow the ION device to peer with a BGP router via the private WAN
interface. Enable
L3 Direct Private WAN Forwarding
and L3
LAN Forwarding
to use dynamic LAN routing. - Select.WorkflowsDevicesClaimed DevicesConfigure the deviceBasic Info
- EnableL3 Direct Private WAN Forwardingto allow the ION device to send underlay MPLS traffic or peer with a BGP router on a private WAN interface.You do not need to enable this field if you intend to run BGP on the internet or standard VPNs.
- EnableL3 LAN Forwardingto use dynamic LAN routing.You can enable Layer 3 LAN Forwarding only when there are no Private Layer 2 bypass pairs associated with any of the interfaces on the device. Starting with Release 5.2.3, if there are Private Layer 2 interfaces on the device, you will see a message to remove the Private Layer 2 interfaces associated with the device and then enable Layer 3 LAN Forwarding.You must enable both EnableL3 Direct Private WAN ForwardingandL3 LAN Forwardingfor the ION device to use dynamic LAN routing.
