Add QoS Policy Sets
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Incidents and Alerts
Add QoS Policy Sets
Learn how to add the QoS policy sets in Prisma SD-WAN,
Where Can I Use This? | What Do I Need? |
---|---|
|
|
A QoS or Priority policy set specifies application
business priority. The policy sets are ordered from left to right in
a stack, with the left-most policy set designated as the highest
priority. You can create a new blank QoS policy set for a site,
clone from an existing stacked policy set or classic policy set,
or create a policy set from a template. You can also create a Default
Rule QoS policy set. A QoS Policy Set comes with two default rules—Default
and Enterprise Default.
- Select ManagePoliciesQoSQoS StacksAdvancedQoS Sets.
- Select Add Set and then Add QoS Policy Set.
- Choose the following options on Add QoS Policy
Set to create a new policy set:
- Default Rule Policy Set—This creates a policy set with two default rules—Default Rule and Enterprise Default Rule.
- Create from Template—Select a template for cloning. The template option creates a set of rules from a template that is defined by Palo Alto Networks. You can customize these rules after creation.
- Clone from Policy Set—Select an existing policy from Stacked Policies for cloning.
- Clone from Original Policy Set—Select an existing policy from Policies (Original) for cloning.
You can create a blank policy set with no rules, if you don't choose any of the above options. - Enter a Name and optionally a Description and Tags for the policy set.
- Click Done.Next, Add QoS Policy Rules to QoS policy sets.