End-of-Life (EoL)
The libvirt API that is used to manage KVM includes a host of tools that allow you to create and manage virtual machines. To install the VM-Series firewall on KVM you can use any of the following methods:
Manually create the XML definition of the VM-Series firewall, then use virsh to import the definition. Virsh is the most powerful tool that allows for full administration of the virtual machine. Use virt-install to create the definition for the VM-Series firewall and install it. Use the desktop user interface called virt-manager; virt-manager provides a convenient wizard to help you through the installation process.
The following procedure uses virt-manager to install the VM-Series firewall on a server running KVM on RHEL; the instructions for using virsh or virt-install are not included in this document.
If you are deploying several VM-Series firewalls and want to automate the initial configuration on the firewall, see Use an ISO File to Deploy the VM-Series Firewall.
Install the VM-Series on KVM
Install the VM-Series firewall. On the Virt-manager, select Create a new virtual machine. Add a descriptive Name for the VM-Series firewall.
Select Import existing disk image, browse to the image, and set the OS Type: Linux and Version: Red Hat Enterprise Linux 6. If you prefer, you can leave the OS Type and Version as Generic.
Set the Memory to 4096 MB; or 5120 MB, if you have purchased the VM-1000-HV license. Set CPU to 2, 4, or 8.
Select Customize configuration before install. Under Advanced options, select the bridge for the management interface, and accept the default settings.
To modify disk settings: Select Disk, expand Advanced options and select Storage format — qcow2; Disk Bus —Virtio or IDE, based on your set up. If you want to use a SCSI disk bus, see Enable the Use of a SCSI Controller. Expand Performance options, and set Cache mode to writethrough. This setting improves installation time and execution speed on the VM-Series firewall.
To add network adapters for the data interfaces: On Ubuntu 16.04 LTS, to pass L2 traffic when using an Open vSwitch, you must set the interface type to bridge and the virtual port type to openvswitch Select Add Hardware > Network if you are using a software bridge such as the Linux bridge or the Open vSwitch. For Host Device, enter the name of the bridge or select it from the drop down list. To specify the driver, set Device Model to e-1000 or virtio. These are the only supported virtual interface types.
Select Add Hardware > PCI Host Device for PCI-passthrough or an SR-IOV capable device.
In the Host Device list, select the interface on the card or the virtual function. Click Apply or Finish. Click Begin Installation .
By default, the XML template for the VM-Series firewall is created and stored at etc/libvirt/qemu. Wait 5-7 minutes for the installation to complete.
(optional) Bootstrap the VM-Series firewall If you are using bootstrapping to perform the configuration of your VM-Series firewall on KVM, refer to Bootstrap the VM-Series Firewall on KVM. For more information about bootstrapping, see Bootstrap the VM-Series Firewall.
Configure the network access settings for the management interface. Open a connection to the console. Log into the firewall with username/password: admin/admin. Enter configuration mode with the following command: configure Use the following command to configure the management interface: set deviceconfig system ip-address <Firewall-IP> netmask <netmask> default-gateway <gateway-IP> dns-setting servers primary <DNS-IP> where <Firewall-IP> is the IP address you want to assign to the management interface, <netmask> is the subnet mask, <gateway-IP> is the IP address of the network gateway, and <DNS-IP> is the IP address of the DNS server.
Verify which ports on the host are mapped to the interfaces on the VM-Series firewall. In order to verify the order of interfaces on the Linux host, see Verify PCI-ID for Ordering of Network Interfaces on the VM-Series Firewall. To make sure that traffic is handled by the correct interface, use the following command to identify which ports on the host are mapped to the ports on the VM-Series firewall. admin@PAN-VM> debug show vm-series interfaces all Phoenix_interface Base-OS_port Base-OS_MAC PCI-ID mgt eth0 52:54:00:d7:91:52 0000:00:03.0 Ethernet1/1 eth1 52:54:00:fe:8c:80 0000:00:06.0 Ethernet1/2 eth2 0e:c6:6b:b4:72:06 0000:00:07.0 Ethernet1/3 eth3 06:1b:a5:7e:a5:78 0000:00:08.0 Ethernet1/4 eth4 26:a9:26:54:27:a1 0000:00:09.0 Ethernet1/5 eth5 52:54:00:f4:62:13 0000:00:10.0
Access the web interface of the VM-Series firewall and configure the interfaces and define security rules and NAT rules to safely enable the applications that you want to secure. Refer to the PAN-OS Administrator’s Guide.

Recommended For You