Configure a Static Route
Perform the following task to configure Static Routes or a default route for a virtual router on the firewall.
- Configure a static route.
- Select NetworkVirtual Router and select the virtual router you are configuring, such as default.
- Select the Static Routes tab.
- Select IPv4 or IPv6, depending on the type of static route you want to configure.
- Add a Name for the route.
- For Destination, enter the route and netmask (for example, 192.168.2.2/24 for an IPv4 address or 2001:db8:123:1::1/64 for an IPv6 address). If you’re creating a default route, enter the default route (0.0.0.0/0 for an IPv4 address or ::/0 for an IPv6 address).
- (Optional) For Interface, specify the outgoing interface for packets to use to go to the next hop. Use this for stricter control over which interface the firewall uses rather than the interface in the route table for the next hop of this route.
- For Next Hop, select one of
- IP Address—Enter the IP address (for example, 192.168.56.1 or 2001:db8:49e:1::1) when you want to route to a specific next hop. You must Enable IPv6 on the interface (when you Configure Layer 3 Interfaces) to use an IPv6 next hop address. If you’re creating a default route, for Next Hop you must select IP Address and enter the IP address for your Internet gateway (for example, 192.168.56.1 or 2001:db8:49e:1::1).
- Next VR—Select this option and then select a virtual router if you want to route internally to a different virtual router on the firewall.
- Discard—Select to drop packets that are addressed to this destination.
- None—Select if there is no next hop for the route. For example, a point-to-point connection needs no next hop because there is only one way for packets to go.
- Enter an Admin Distance for the route to override the default administrative distance set for static routes for this virtual router (range is 10-240; default is 10).
- Enter a Metric for the route (range is 1-65,535).
- Choose where to install the route.Select the Route Table (the RIB) into which you want the firewall to install the static route:
- Unicast—Install the route in the unicast route table. Choose this option if you want the route used only for unicast traffic.
- Multicast—Install the route in the multicast route table (available for IPv4 routes only). Choose this option if you want the route used only for multicast traffic.
- Both—Install the route in the unicast and multicast route tables (available for IPv4 routes only). Choose this option if you want either unicast or multicast traffic to use the route.
- No Install—Do not install the route in either route table.
- (Optional) If your firewall model supports BFD, you can apply a BFD Profile to the static route so that if the static route fails, the firewall removes the route from the RIB and FIB and uses an alternative route. Default is None.
- Click OK twice.
- Commit the configuration.Click Commit.
Configure a BGP Peer with MP-BGP for IPv4 Multicast
Configure a BGP Peer with MP-BGP for IPv4 Multicast After you Configure BGP , configure a BGP peer with MP-BGP for IPv4 multicast if you ...
Static Route Overview
Static Route Overview If you decide that you want specific Layer 3 traffic to take a certain route without participating in IP routing protocols, you ...
Configure a BGP Peer with MP-BGP for IPv4 or IPv6 Unicast
Configure a BGP Peer with MP-BGP for IPv4 or IPv6 Unicast After you Configure BGP , configure a BGP peer with MP-BGP for IPv4 or ...
Routing Tab The following table describes the virtual router’s runtime stats for the Route Table , Forwarding Table , and the Static Route Monitoring table. ...
Static Routes Network > Virtual Routers > Static Routes Optionally add one or more static routes. Click the IP or IPv6 tab to specify the ...
MP-BGP BGP supports IPv4 unicast prefixes, but a BGP network that uses IPv4 multicast routes or IPv6 unicast prefixes needs multiprotocol BGP (MP-BGP) in order ...
Configure Path Monitoring for a Static Route
Configure Path Monitoring for a Static Route Use the following procedure to configure Static Route Removal Based on Path Monitoring . Enable path monitoring for ...
PIM uses reverse-path forwarding (RPF) to prevent routing loops and to build a shortest-path tree from the receiver back to the multicast source. ...
BGP Conditional Adv Tab
BGP Conditional Adv Tab Network > Virtual Router > BGP > Conditional Adv A BGP conditional advertisement allows you to control which route to advertise ...