Device > Setup > Management
Table of Contents
9.1 (EoL)
Expand all | Collapse all
-
- Objects > Addresses
- Objects > Address Groups
- Objects > Regions
- Objects > Dynamic User Groups
- Objects > Application Groups
- Objects > Application Filters
- Objects > Services
- Objects > Service Groups
- Objects > External Dynamic Lists
- Objects > Custom Objects > Spyware/Vulnerability
- Objects > Custom Objects > URL Category
- Objects > Security Profiles > Antivirus
- Objects > Security Profiles > Anti-Spyware Profile
- Objects > Security Profiles > Vulnerability Protection
- Objects > Security Profiles > File Blocking
- Objects > Security Profiles > WildFire Analysis
- Objects > Security Profiles > Data Filtering
- Objects > Security Profiles > DoS Protection
- Objects > Security Profiles > GTP Protection
- Objects > Security Profiles > SCTP Protection
- Objects > Security Profile Groups
- Objects > Log Forwarding
- Objects > Authentication
- Objects > Decryption > Forwarding Profile
- Objects > Schedules
-
-
- Firewall Interfaces Overview
- Common Building Blocks for Firewall Interfaces
- Common Building Blocks for PA-7000 Series Firewall Interfaces
- Tap Interface
- HA Interface
- Virtual Wire Interface
- Virtual Wire Subinterface
- PA-7000 Series Layer 2 Interface
- PA-7000 Series Layer 2 Subinterface
- PA-7000 Series Layer 3 Interface
- Layer 3 Interface
- Layer 3 Subinterface
- Log Card Interface
- Log Card Subinterface
- Decrypt Mirror Interface
- Aggregate Ethernet (AE) Interface Group
- Aggregate Ethernet (AE) Interface
- Network > Interfaces > VLAN
- Network > Interfaces > Loopback
- Network > Interfaces > Tunnel
- Network > Interfaces > SD-WAN
- Network > VLANs
- Network > Virtual Wires
-
- Network > Network Profiles > GlobalProtect IPSec Crypto
- Network > Network Profiles > IPSec Crypto
- Network > Network Profiles > IKE Crypto
- Network > Network Profiles > Monitor
- Network > Network Profiles > Interface Mgmt
- Network > Network Profiles > QoS
- Network > Network Profiles > LLDP Profile
- Network > Network Profiles > SD-WAN Interface Profile
-
-
- Device > Setup
- Device > Setup > Management
- Device > Setup > Interfaces
- Device > Setup > Telemetry
- Device > Setup > Content-ID
- Device > Setup > WildFire
- Device > Log Forwarding Card
- Device > Config Audit
- Device > Administrators
- Device > Admin Roles
- Device > Access Domain
- Device > Authentication Sequence
-
- Security Policy Match
- QoS Policy Match
- Authentication Policy Match
- Decryption/SSL Policy Match
- NAT Policy Match
- Policy Based Forwarding Policy Match
- DoS Policy Match
- Routing
- Test Wildfire
- Threat Vault
- Ping
- Trace Route
- Log Collector Connectivity
- External Dynamic List
- Update Server
- Test Cloud Logging Service Status
- Test Cloud GP Service Status
- Device > Virtual Systems
- Device > Shared Gateways
- Device > Certificate Management
- Device > Certificate Management > Certificate Profile
- Device > Certificate Management > OCSP Responder
- Device > Certificate Management > SSL/TLS Service Profile
- Device > Certificate Management > SCEP
- Device > Certificate Management > SSL Decryption Exclusion
- Device > Response Pages
- Device > Server Profiles
- Device > Server Profiles > SNMP Trap
- Device > Server Profiles > Syslog
- Device > Server Profiles > Email
- Device > Server Profiles > HTTP
- Device > Server Profiles > NetFlow
- Device > Server Profiles > RADIUS
- Device > Server Profiles > TACACS+
- Device > Server Profiles > LDAP
- Device > Server Profiles > Kerberos
- Device > Server Profiles > SAML Identity Provider
- Device > Server Profiles > DNS
- Device > Server Profiles > Multi Factor Authentication
- Device > Local User Database > Users
- Device > Local User Database > User Groups
- Device > Scheduled Log Export
- Device > Software
- Device > Dynamic Updates
- Device > Licenses
- Device > Support
-
- Network > GlobalProtect > MDM
- Network > GlobalProtect > Device Block List
- Network > GlobalProtect > Clientless Apps
- Network > GlobalProtect > Clientless App Groups
- Objects > GlobalProtect > HIP Profiles
-
- Use the Panorama Web Interface
- Context Switch
- Panorama Commit Operations
- Defining Policies on Panorama
- Log Storage Partitions for a Panorama Virtual Appliance in Legacy Mode
- Panorama > Setup > Interfaces
- Panorama > High Availability
- Panorama > Administrators
- Panorama > Admin Roles
- Panorama > Access Domains
- Panorama > Device Groups
- Panorama > Plugins
- Panorama > Log Ingestion Profile
- Panorama > Log Settings
- Panorama > Scheduled Config Export
End-of-Life (EoL)
Device > Setup > Management
- DeviceSetupManagement
- PanoramaSetupManagement
On a firewall, select DeviceSetupManagement to
configure management settings.
On Panorama™, select DeviceSetupManagement to
configure firewalls that you manage with Panorama templates. Select PanoramaSetupManagement to
configure management settings for Panorama.
The following management settings apply to both the firewall
and Panorama except where noted.
- Panorama Settings: Device > Setup > Management (settings configured on the firewall to connect to Panorama)
- Panorama Settings: Panorama > Setup > Management (settings configured on Panorama for connections to firewalls)
- Logging Service
Item | Description |
---|---|
General Settings | |
Hostname | Enter a host name (up to 31 characters).
The name is case-sensitive, must be unique, and can contain only
letters, numbers, periods, hyphens, and underscores. If you
don’t enter a value, PAN-OS® uses the firewall model (for example,
PA-5220_2) as the default. Optionally, you can configure the
firewall to use a hostname that a DHCP server provides. See Accept
DHCP server-provided Hostname (Firewall only). Configure a unique host name to easily
identify the device you are managing. |
Domain | Enter the network domain name for the firewall
(up to 31 characters). Optionally, you can configure the firewalls
and Panorama to use a domain that a DHCP server provides. See Accept
DHCP server-provided Domain (Firewall only). |
Accept DHCP server-provided
Hostname (Firewall only) | (Applies only when the Management Interface
IP Type is DHCP Client.) Select this option to have the management
interface accept the hostname it receives from the DHCP server.
The hostname from the server (if valid) overwrites any value specified
in the Hostname field. |
Accept DHCP server-provided
Domain (Firewall only) | (Applies only when the Management Interface
IP Type is DHCP Client.) Select this option to have the management
interface accept the domain (DNS suffix) it receives from the DHCP
server. The domain from the server overwrites any value specified
in the Domain field. |
Login Banner | Enter text (up to 3,200 characters) to display
on the web interface login page below the Name and Password fields. |
Force Admins to Acknowledge Login Banner | Select this option to display and force
administrators to select I Accept and Acknowledge the Statement
Below above the login banner on the login page, which
forces administrators to acknowledge that they understand and accept
the contents of the message before they can Login. |
SSL/TLS Service Profile | Assign an existing SSL/TLS Service profile
or create a new one to specify a certificate and the SSL/TLS protocol settings
allowed on the management interface (see Device
> Certificate Management > SSL/TLS Service Profile). The
firewall or Panorama uses this certificate to authenticate to administrators
who access the web interface through the management (MGT) interface
or through any other interface that supports HTTP/HTTPS management
traffic (see Network
> Network Profiles > Interface Mgmt). If you select none (default),
the firewall or Panorama uses a predefined certificate. The predefined certificate is provided
for convenience. For better security, assign an SSL/TLS Service
profile. To ensure trust, the certificate must be signed by a certificate
authority (CA) certificate that is in the trusted root certificate
store of the client systems. |
Time Zone | Select the time zone of the firewall. |
Locale | Select a language for PDF reports from the
drop-down. See Monitor
> PDF Reports > Manage PDF Summary. Even if you have
a specific language preference set for the web interface, PDF reports
will use the language specified for Locale. |
Date | Set the date on the firewall; enter the
current date (in YYYY/MM/DD format) or select the date from the drop-down. You
can also define an NTP server (DeviceSetupServices). |
Time | Set the time on the firewall; enter the
current time) in 24-hour format) or select the time from the drop-down. You
can also define an NTP server (DeviceSetupServices). |
Serial Number (Panorama virtual appliances
only) | Enter the serial number for Panorama. You
can find the serial number in the order fulfillment email you received
from Palo Alto Networks®. |
Latitude | Enter the latitude (-90.0 to 90.0) of the
firewall. |
Longitude | Enter the longitude (-180.0 to 180.0) of
the firewall. |
Automatically acquire commit lock | Select this option to automatically apply
a commit lock when you change the candidate configuration. For more information,
see Lock
Configurations. Enable Automatically
Acquire Commit Lock so that other administrators can’t
make configuration changes until the first administrator commits
her/his changes. |
Certificate Expiration Check | Instruct the firewall to create warning
messages when on-box certificates approach their expiration date. Enable Certificate Expiration
Check to generate a warning message when on-box certificates
approach their expiration date. |
Multiple Virtual System Capability | Enables the use of multiple virtual systems
on firewalls that support this feature (see Device
> Virtual Systems). To enable
multiple virtual systems on a firewall, firewall policies must reference
no more than 640 distinct user groups. If necessary, reduce the
number of referenced user groups. Then, after you enable and add
multiple virtual systems, the policies can then reference another
640 user groups for each additional virtual system. |
URL Filtering Database (Panorama only) | Select a URL Filtering vendor for use with
Panorama: brightcloud or paloaltonetworks (PAN-DB). |
Use Hypervisor Assigned MAC Addresses (VM-Series
firewalls only) | Select this option to have the VM-Series
firewall use the MAC address that the hypervisor assigned, instead
of generating a MAC address using the PAN-OS custom schema. If
you enable this option and use an IPv6 address for the interface,
the interface ID cannot use the EUI-64 format, which derives the
IPv6 address from the interface MAC address. In a high availability
(HA) active/passive configuration, a commit error occurs if you
use the EUI-64 format. |
GTP Security | Select this option to enable the ability
to inspect the control plane and user dataplane messages in the
GPRS Tunneling Protocol (GTP) traffic. See Objects
> Security Profiles > GTP Protection to configure a GTP protection
profile so that you can enforce policy on GTP traffic. |
SCTP Security | Select this option to enable the ability
to inspect and filter Stream Control Transmission Protocol (SCTP)
packets and chunks, and to apply SCTP initiation (INIT) flood protection.
See Objects
> Security Profiles > SCTP Protection. For SCTP INIT flood
protection, see Configure SCTP INIT Flood Protection. |
Device Certificate (PAN-OS
9.1.3 and later releases only) | |
Get certificate | Click to enter the One Time Password (OTP)
generated from the Palo Alto Networks Customer Support Portal.
The device certificate is required to successfully authenticate
Panorama with the CSP and leverage Zero Touch Provisioning (ZTP).
After you successfully install the device certificate, the following
is displayed:
|
Authentication
Settings | |
Authentication Profile | Select the authentication profile (or sequence)
the firewall uses to authenticate administrative accounts that you define
on an external server instead of locally on the firewall (see Device
> Authentication Profile). When external administrators log
in, the firewall requests authentication and authorization information
(such as the administrative role) from the external server. Enabling
authentication for external administrators requires additional steps
based on the server type that the authentication profile specifies,
which must be one of the following:
Administrators
can use SAML to authenticate to the web interface but not to the CLI. Select None to
disable authentication for external administrators. For administrative
accounts that you define locally (on the firewall), the firewall
authenticates using the authentication profile assigned to those
accounts (see Device
> Administrators). |
Certificate Profile | Select a certificate profile to verify the
client certificates of administrators who are configured for certificate-based access
to the firewall web interface. For instructions on configuring certificate
profiles, see Device
> Certificate Management > Certificate Profile. Configure a certificate profile to ensure
that the administrator’s host machine has the right certificates
to authenticate with the Root CA certificate defined in the certificate
profile. |
Idle Timeout | Enter the maximum time (in minutes) without
any activity on the web interface or CLI before an administrator
is automatically logged out (range is 0 to 1,440; default is 60). A
value of 0 means that inactivity does not trigger an automatic logout. Both manual and automatic refreshing of
web interface pages (such as the Dashboard and
System Alarms dialog) reset the Idle Timeout counter.
To enable the firewall to enforce the timeout when you are on a
page that supports automatic refreshing, set the refresh interval
to Manual or to a value higher than the Idle
Timeout. You can also disable Auto Refresh in
the ACC tab. Set
the Idle Timeout to 10 minutes to prevent
unauthorized users from accessing the firewall if an administrator
leaves a firewall session open. |
API Key Lifetime | Enter the length of time (in minutes) for
which the API key is valid (range is 0 to 525,600; default is 0).
A value of 0 means that the API key never expires. Expire
All API Keys to invalidate all previously generated
API keys. Use this option with caution because all existing keys
are rendered useless and any operation where you are currently using
those API keys will stop functioning. Perform
this operation during a maintenance window so that you can replace
the keys without disrupting current implementations where you referenced
the API keys. |
API Keys Last Expired | Displays the timestamp of when the API key
last expired. This field has no value if you have never reset your keys. |
Failed Attempts | Enter the number of failed login attempts
(0 to 10) that the firewall allows for the web interface and CLI
before locking out the administrator account. A value of 0 specifies unlimited
login attempts. The default value is 0 for firewalls in normal operational
mode and 10 for firewalls in FIPS-CC mode. Limiting login attempts
can help protect the firewall from brute force attacks. If you set the Failed Attempts to
a value other than 0 but leave the Lockout Time at
0, the Failed Attempts is ignored and the user
is never locked out. Set the
number of Failed Attempts to 5 or fewer to accommodate
a reasonable number of retries in case of typing errors, while preventing
malicious systems from trying brute force methods to log in to the
firewall. |
Lockout Time | Enter the number of minutes (range is 0
to 60) for which the firewall locks out an administrator from access
to the web interface and CLI after reaching the Failed
Attempts limit. A value of 0 (default) means the lockout
applies until another administrator manually unlocks the account. If you set the Failed Attempts to
a value other than 0 but leave the Lockout Time at
0, the user is locked out after the set number of failed login attempts
until another administrator manually unlocks the account. Set the Lockout Time to
at least 30 minutes to prevent continuous login attempts from a
malicious actor. |
Policy
Rulebase Settings | |
Require Tag on Policies | Requires at least one tag when creating
a new policy rule. If a policy rule already exists when you enable
this option, you must add at least one tag the next time you edit the
rule. |
Require Description on Policies | Requires that you add a Description when
you create a new policy rule. If a policy rule already exists when
you enable this option, you must add a Description the
next time you edit the rule. |
Fail Commit if Policies Have No Tags or
Descriptions | Forces your commit to fail if you do not
add any tags or a description to the policy rule. If a policy rule
already exists when you enable this option, the commit will fail
if no tag or description are added the next time you edit the rule. To
fail the commit, you must Require tag on policies or Require description
on policies. |
Require Audit Comment on Policies | Requires Audit Comment when
creating a new policy rule. If a policy rule already exists when
you enable this option, you must add Audit Comment the
next time you edit the rule. |
Audit Comment Regular Expression | Specify requirements for the comment format parameters
in audit comments. |
Policy Rule Hit Count | Tracks how often traffic matches the policy
rules you configured on the firewall. When enabled, you can view
the total Hit Count for total traffic matches against each rule along
with the date and time when the rule was Created, Modified, was
First Hit and Last Hit. |
Policy Application Usage | |
Panorama Settings:
Device > Setup > Management Configure the following settings
on the firewall or in a template on Panorama. These settings establish
a connection from the firewall to Panorama. You must also
configure connection and object sharing settings on Panorama (Panorama
Settings: Panorama > Setup > Management). The
firewall uses an SSL connection with AES256 encryption to register
with Panorama. By default, Panorama and the firewall authenticate
each other using predefined 2,048-bit certificates and they use
the SSL connection for configuration management and log collection.
To further secure the SSL connections between Panorama, firewalls,
and log collectors, see Secure
Client Communication to configure custom certificates between
the firewall and Panorama or a log collector. | |
Panorama Servers | Enter the IP address or FQDN of the Panorama
server. If Panorama is in a high availability (HA) configuration,
in the second Panorama Servers field, enter
the IP address or FQDN of the secondary Panorama server. |
Receive Timeout for Connection to Panorama | Enter the timeout (in seconds) for receiving
TCP messages from Panorama (range is 1 to 240; default is 240). |
Send Timeout for Connection to Panorama | Enter the timeout (in seconds) for sending
TCP messages to Panorama (range is 1 to 240; default is 240). |
Retry Count for SSL Send to Panorama | Enter the number of retry attempts allowed
when sending Secure Socket Layer (SSL) messages to Panorama (range
is 1 to 64; default is 25). |
Enable Automated Commit Recovery | Enable to enable the firewall to automatically
verify its connection to the Panorama management server when a configuration
is committed and pushed to the firewall, and at configured intervals
after a configuration is successfully pushed. When enabled,
and the firewall fails to verify its connection to the Panorama
management server, the firewall and Panorama management automatically
revert their configuration to the previous running configuration
to restore connectivity. |
Number of attempts to check for Panorama connectivity | When Enabled Automated Commit Recovery is
enabled, configure the number of times the firewall tests its connection
to the Panorama management server. |
Interval between retries (sec) | When Enable Automated Commit Recovery is
enabled, configure the time in seconds between the number of attempts
the firewall tests its connection to the Panorama management server. |
Secure
Client Communication | Enable Secure Client Communication to
ensure that the firewall uses configured custom certificates (instead
of the default certificate) to authenticate SSL connections with
Panorama or log collectors.
|
| |
Disable/Enable Panorama Policy and Objects | This option displays only when you edit
the Panorama Settings on a firewall (not
in a template on Panorama). Disable Panorama Policy
and Objects to disable the propagation of device group
policies and objects to the firewall. By default, this action also
removes those policies and objects from the firewall. To keep a
local copy of the device group policies and objects on the firewall,
in the dialog that opens when you click this option, select Import
Panorama Policy and Objects before disabling. After
you perform a commit, these policies and objects become part of the
firewall configuration and Panorama no longer manages them. For
multi-vsys firewalls, you must first import the the template configuration
and then import the device group configuration to successfully disable
the Panorama pushed configuration. Under normal operating
conditions, disabling Panorama management is unnecessary and could
complicate the maintenance and configuration of firewalls. This
option generally applies to situations where firewalls require rules and
object values that differ from those defined in the device group.
An example is when you move a firewall out of production and into
a laboratory environment for testing. To revert firewall policy
and object management to Panorama, click Enable Panorama
Policy and Objects. |
Disable/Enable Device and Network Template | This option displays only when you edit
the Panorama Settings on a firewall (not
in a template on Panorama). Disable Device and
Network Template to disable the propagation of template information
(device and network configurations) to the firewall. By default,
this action also removes the template information from the firewall.
To keep a local copy of the template information on the firewall,
in the dialog that opens when you select this option, select Import Device
and Network Templates before disabling. After you perform
a commit, the template information becomes part of the firewall configuration
and Panorama no longer manages that information. For
multi-vsys firewalls, you must first import the the template configuration
and then import the device group configuration to successfully disable
the Panorama pushed configuration. Under
normal operating conditions, disabling Panorama management is unnecessary
and could complicate the maintenance and configuration of firewalls. This
option generally applies to situations where firewalls require device
and network configuration values that differ from those defined
in the template. An example is when you move a firewall out of production
and into a laboratory environment for testing. To configure
the firewall to accept templates again, click Enable
Device and Network Templates. |
Panorama Settings:
Panorama > Setup > Management If you use Panorama to manage
firewalls, configure the following settings on Panorama. These settings
determine timeouts and SSL message attempts for the connections
from Panorama to managed firewalls, as well as object sharing parameters. You
must also configure Panorama connection settings on the firewall
or in a template on Panorama: see Panorama
Settings: Device > Setup > Management. The firewall
uses an SSL connection with AES256 encryption to register with Panorama.
By default, Panorama and the firewall authenticate each other using
predefined 2,048-bit certificates and they use the SSL connection
for configuration management and log collection. To further secure
these SSL connections, see Customize
Secure Server Communication to configure custom certificates
between Panorama and its clients. | |
Receive Timeout for Connection to Device | Enter the timeout (in seconds) for receiving
TCP messages from all managed firewalls (range is 1 to 240; default
is 240). |
Send Timeout for Connection to Device | Enter the timeout (in seconds) for sending
TCP messages to all managed firewalls (range is 1 to 240; default is
240). |
Retry Count for SSL Send to Device | Enter the number of allowed retry attempts
when sending Secure Socket Layer (SSL) messages to managed firewalls
(range is 1 to 64; default is 25). |
Share Unused Address and Service Objects
with Devices | Select this option (enabled by default)
to share all Panorama shared objects and device-group-specific objects with
managed firewalls. If you disable this option, the appliance
checks Panorama policies for references to address, address group, service,
and service group objects, and does not share any unreferenced objects.
This option reduces the total object count by ensuring that the
appliance sends only necessary objects to managed firewalls. If
you have a policy rule that targets specific devices in a device
group, then the objects used in that policy are considered used
in that device group. |
Objects defined in ancestors
will take higher precedence | Select this option (disabled by default)
to specify that the object values in ancestor groups take precedence
over those in descendant groups when device groups at different levels
in the hierarchy have objects of the same type and name but with
different values. This means that when you perform a device group
commit, the ancestor values replace any override values. Likewise,
this option causes the value of a shared object to override the
values of objects of the same type and name in device groups. Selecting
this option displays the Find
Overridden Objects link. |
Find Overridden Objects | Select this option (bottom of the Panorama
Settings dialog) to list any shadowed objects. A shadowed
object is an object in the Shared location that has the same name
but a different value in a device group. The link displays only
if you specify that Objects
defined in ancestors will take higher precedence. |
Enable
reporting and filtering on groups | Select this option (disabled by default)
to enable Panorama to locally store usernames, user group names,
and username-to-group mapping information that it receives from firewalls.
This option is global to all device groups in Panorama. However,
you must also enable local storage at the level of each device group
by specifying a Master
Device and configuring the firewall to Store
users and groups from Master Device. |
Secure Communication Settings: Panorama > Setup > Management | |
Customize
Secure Server Communication |
|
Secure Client Communications | Using Secure Client Communication ensures
that the client Panorama uses configured custom certificates (instead
of the default predefined certificate) to authenticate SSL connections
with another Panorama appliance in an HA pair or WildFire appliance.
|
Logging and Reporting
Settings Use this section to modify:
| |
Log Storage tab (Panorama management
server and all firewall models except PA-5200 Series and PA‑7000
Series firewalls) Panorama displays this tab if
you edit the Logging and Reporting Settings (PanoramaSetupManagement).
If you use a Panorama template to configure the settings for firewalls (DeviceSetupManagement),
see Single
Disk Storage and Multi Disk Storage tabs. | For each log type, specify:
Weekly summary
logs can age beyond the threshold before the next deletion if they
reach the expiration threshold between times when the firewall deletes logs.
When a log quota reaches the maximum size, new log entries start
overwriting the oldest log entries. If you reduce a log quota size,
the firewall or Panorama removes the oldest logs when you commit
the changes. In an HA active/passive configuration, the passive
peer does not receive logs and, therefore, does not delete them
unless failover occurs and the passive peer becomes active. |
To enable or disable the large-core file
option, enter the following CLI command from configuration mode
and then commit the configuration: # set deviceconfig setting management large-core [yes|no] The core file is deleted when you disable
this option. You must use SCP from operational mode
to export the core file: > scp export core-file large-corefile Only
a Palo Alto Networks support engineer can interpret the contents
of the core files.
| |
Session
Log Storage and Management Log Storage tabs (PA-5200
Series and PA‑7000 Series firewalls only) | PA-5200 Series
and PA-7000 Series firewalls store management logs and session
logs on separate disks. Select the tab for each set of logs and
configure the settings described in Log
Storage tab:
|
Single
Disk Storage and Multi Disk Storage tabs (Panorama
template only) | If you use a Panorama template to configure
log quotas and expiration periods, configure the settings in one
or both of the following tabs based on the firewalls assigned to
the template:
|
Log Export and Reporting tab | Configure the following log export and reporting settings
as needed:
|
Log Export and Reporting tab (cont) |
|
| |
(Panorama only) |
|
Pre-Defined Reports—Pre-defined reports for application, traffic, threat,
URL Filtering, and Stream Control Transmission Protocol (SCTP) are
available on the firewall and on Panorama. Pre-defined reports for
SCTP are available on the firewall and Panorama after SCTP Security
is enabled in DeviceSetupManagementGeneral Settings. Because
the firewalls consume memory resources in generating the results
hourly (and forwarding it to Panorama where it is aggregated and
compiled for viewing), to reduce memory usage, you can disable the
reports that are not relevant to you. To disable a report, disable
this option for the report. Click Select All or Deselect
All to entirely enable or disable the generation of
pre-defined reports. Before disabling a report, verify
that there isn’t a Group Report or a PDF Report using it. If you disable
a pre-defined report assigned to a set of reports, the entire set
of reports will have no data. | |
Banners and Messages To
view all messages in a Message of the Day dialog, see Message
of the Day. After you configure
the Message of the Day and click OK, administrators
who subsequently log in and active administrators who refresh their
browsers will see the new or updated message immediately; a commit
is not required. This enables you to warn other administrators of
an impending commit before you perform that commit. | |
Message of the Day (check box) | Select this option to enable the Message
of the Day dialog to display when an administrator logs in to the
web interface. |
Message of the Day (text-entry field) | Enter the text (up to 3,200 characters)
for the Message of the Day dialog. |
Allow Do Not Display Again | Select this option (disabled by default)
to include a Do not show again option in
the Message of the Day dialog. This gives administrators the option
to avoid seeing the same message in subsequent logins. If
you modify the Message of the Day text, the
message displays even to administrators who selected Do
not show again. Administrators must reselect this option
to avoid seeing the modified message in subsequent sessions unless
the message is modified again. |
Title | Enter text for the Message of the Day header
(default is Message of the Day). |
Background Color | Select a background color for the Message
of the Day dialog. The default (None) is
a light gray background. |
Icon | Select a predefined icon to appear above
the text in the Message of the Day dialog:
|
Header Banner | Enter the text that the header banner displays
(up to 3,200 characters). |
Header Color | Select a color for the header background.
The default (None) is a transparent background. |
Header Text Color | Select a color for the header text. The
default (None) is black. |
Same banner for header and footer | Select this option (enabled by default)
if you want the footer banner to have the same text and colors as
the header banner. When enabled, the fields for the footer banner
text and colors are grayed out. |
Footer Banner | Enter the text that the footer banner displays
(up to 3,200 characters). |
Footer Color | Select a color for the footer background.
The default (None) is a transparent background. |
Footer Text Color | Select a color for the footer text. The
default (None) is black. |
Minimum Password
Complexity | |
Enabled | Enable minimum password requirements for
local accounts. With this feature, you can ensure that local administrator
accounts on the firewall will adhere to a defined set of password
requirements. You can also create a password profile with
a subset of these options that will override these settings and
can be applied to specific accounts. For more information, see Device
> Password Profiles and see Username
and Password Requirements for information on valid characters
that can be used for accounts. The maximum password
length is 31 characters. Avoid setting requirements that PAN-OS
does not accept. For example, do not set a requirement of 10 uppercase,
10 lower case, 10 numbers, and 10 special characters because that
would exceed the maximum length of 31 characters. If
you have high availability (HA) configured, always use the primary
peer when configuring password complexity options and commit soon
after making changes. Minimum password complexity settings
do not apply to local database accounts for which you specified
a Password Hash (see Device
> Local User Database > Users). Require
strong passwords to help prevent brute force network access attacks
from succeeding. Require a minimum length and the use of at least one
each of uppercase letters, lowercase letters, numerical values,
and special characters. In addition, prevent excessive repetition
of characters and usernames in passwords, set limits on how often
passwords can be reused, and set regular password change periods
so passwords don’t stay in use too long. The stronger the password
requirements, the more difficult you make it for attackers to hack
a password. Be sure to use the best practices for password strength to
ensure a strict password. |
Minimum Length | Require a minimum password length (range
is 1 to 15 characters). |
Minimum Uppercase Letters | Require a minimum number of uppercase letters (ranges
is 0 to 15 characters). |
Minimum Lowercase Letters | Require a minimum number of lowercase letters
(range is 0 to 15 characters). |
Minimum Numeric Letters | Require a minimum number of numeric letters
(range is 0 to 15 numbers). |
Minimum Special Characters | Require a minimum number of special (non-alphanumeric)
characters (range is 0 to 15 characters). |
Block Repeated Characters | Specify the number of sequential duplicate
characters permitted in a password (range is 2 to 15). If
you set the value to 2, the password can contain the same character
in sequence twice but if the same character is used three or more
times in sequence, the password is not permitted. For example,
if the value is set to 2, the system will accept the password test11
or 11test11, but not test111, because the number 1 appears three
times in sequence. |
Block Username Inclusion (including reversed) | Select this option to prevent the account
username (or reversed version of the name) from being used in the password. |
New Password Differs By Characters | When administrators change their passwords,
the characters must differ by the specified value. |
Require Password Change on First Login | Select this option to prompt administrators
to change their passwords the first time they log in to the firewall. |
Prevent Password Reuse Limit | Require that a previous password is not
reused based on the specified count. For example, if the value is
set to 4, you could not reuse any of your last 4 passwords (range
is 0 to 50). |
Block Password Change Period (days) | User cannot change their passwords until
the specified number of days is reached (range is 0 to 365 days). |
Required Password Change Period (days) | Require that administrators change their
password on a regular basis (in days) (range is 0 to 365). For example,
if the value is set to 90, administrators are prompted to change their
password every 90 days. You can also set an expiration warning
from 0 to 30 days and specify a grace period. |
Expiration Warning Period (days) | If a Required Password Change Period is
set, you can use this Expiration Warning Period to prompt
users at each log in to change their password when there are less
than a specified number of days remaining before the required change
date (range is 0 to 30). |
Post Expiration Admin Login Count (count) | Allow the administrator to log in a specified
number of times after the required change date (range is 0 to 3).
For example, if you set this value to 3 and their account has expired,
they can log in 3 more times without changing their password before
their account is locked out. |
Post Expiration Grace Period (days) | Allow the administrator to log in for a
specified number of days after the account has expired (range is
0 to 30). |
AutoFocus™ | |
Enabled | Enable the firewall to connect to an AutoFocus
portal to retrieve threat intelligence data and to enable integrated searches
between the firewall and AutoFocus. When connected to AutoFocus,
the firewall displays AutoFocus data associated with Traffic, Threat,
URL Filtering, WildFire Submissions, and Data Filtering log entries (MonitorLogs).
You can click on an artifact in these types of log entries (such
as an IP address or a URL) to display a summary of the AutoFocus findings
and statistics for that artifact. You can then open an expanded
AutoFocus search for the artifact directly from the firewall. Check that your AutoFocus license is active
on the firewall (DeviceLicenses).
If the AutoFocus license is not displayed, use one of the License
Management options to activate the license. |
AutoFocus URL | Enter the AutoFocus URL: https://autofocus.paloaltonetworks.com:10443 |
Query Timeout (sec) | Set the duration of time (in seconds) for
the firewall to attempt to query AutoFocus for threat intelligence
data. If the AutoFocus portal does not respond before the end of
the specified period, the firewall closes the connection. |
Logging
Service Use this section to configure VM-Series and hardware-based
firewalls to forward logs to Cortex Data Lake. Here’s the full workflow
to configure the options described below:
The
Logging Service is now called Cortex Data Lake; however, some firewall features
and buttons still display the Logging Service name. | |
Enable Logging Service | Pick this option to enable the firewall
(or, if you’re using Panorama, firewalls that belong to the selected Template)
to forward logs to Cortex Data Lake (Cortex Data Lake was previously
called the Logging Service). After you configure Log Forwarding
(Objects
> Log Forwarding), the firewall forwards logs directly to Cortex
Data Lake—this is true even for Panorama-managed firewalls. |
Enable Duplicate Logging (for Panorama-managed
firewalls only) | Enable Duplicate Logging to
continue to send logs to Panorama and distributed Log Collectors,
in addition to sending logs to Cortex Data Lake. This is
a helpful option if you’re evaluating Cortex Data Lake—when enabled,
the firewalls that belong to the selected Template will save a copy
of the logs to Cortex Data Lake and to your Panorama or Distributed
Log Collection architecture. |
Enable Enhanced Application Logging | Enable Enhanced Application Logging if
you want the firewall to collect data that increases network visibility
for Palo Alto Networks applications. For example, this increased
network visibility enables Palo Alto Networks Cortex XDR apps to
better categorize and establish a baseline for normal network activity
so that the firewall can detect unusual behavior that might indicate
an attack. Enhanced Application Logging requires a Logging Service
(Cortex Data Lake) license. You cannot view these logs—they are
designed to be consumed only by Palo Alto Networks applications. |
Region | Select the geographic region
of Cortex Data Lake (Logging Service) instance to which the firewall
will forward logs. Log in to the Cortex hub to confirm
the region in which a Cortex Data Lake instance is deployed (in the
hub, select the settings gear on the top menu bar and click Manage
Apps). |
Connection count to Logging
Service for PA-7000s and PA-5200s | (PA-7000 Series and PA-5200
Series firewalls) Specify the number of connections for sending logs
from the firewalls to Cortex Data Lake (range is 1 to 20; default
is 5). You can use the request logging-service-forwarding status CLI command
on the firewall to verify the number of active connections between
the firewall and Cortex Data Lake. |
Onboard without Panorama (for
firewalls that are not managed by Panorama) | You can enable firewalls that are not managed by Panorama to log to Cortex Data Lake. To do this, you’ll need to first generate a key in the Cortex Data Lake app. This key enables the firewall to authenticate and securely connect to Cortex Data Lake. After you’ve generated the key, enter it here. Then, continue to enable the firewall to start forwarding logs to Cortex Data Lake. |
Logging
Service Status | View the status of the connection to Cortex
Data Lake. Show Status to view the details
for the following checks:
|