Interface Name

Comment

(Optional) Enter a description for the interface.

Interface Type

Select Aggregate Ethernet.

Aggregate Group

Link Speed

Link Duplex

Link State

LACP Port Priority

Virtual Router

Security Zone

Select the security zone to which you assign the Aggregate Ethernet interface.

Enable Bonjour Reflector

Enable IPv6 on the interface

Interface ID

Enter the 64-bit extended unique identifier (EUI-64) in hexadecimal format (for example, 00:26:08:FF:FE:DE:4E:29). If you leave this field blank, the firewall uses the EUI-64 generated from the MAC address of the physical interface. If you Use interface ID as host portion when adding an address, the firewall uses the interface ID as the host portion of that address.

Address

Add an IPv6 address and configure the following parameters:

Enable Duplication Address Detection

DAD Attempts

Specify the number of DAD attempts within the neighbor solicitation interval (NS Interval) before the attempt to identify neighbors fails (range is 1-10; default is 1).

Reachable Time

Specify the length of time, in seconds, that a neighbor remains reachable after a successful query and response (range is 1-36,000; default is 30).

NS Interval (neighbor solicitation interval)

Specify the length of time, in seconds, before a DAD attempt failure is indicated (range is 1-10; default is 1).

Enable NDP Monitoring

Select to enable Neighbor Discovery Protocol monitoring. When enabled, you can select the NDP ( in Features column) and view information such as the IPv6 address of a neighbor the firewall has discovered, the corresponding MAC address and User-ID (on a best-case basis).

Enable Router Advertisement

Min Interval (sec)

Specify the minimum interval, in seconds, between RAs that the firewall will send (range is 3-1,350; default is 200). The firewall will send RAs at random intervals between the minimum and maximum values you configure.

Max Interval (sec)

Specify the maximum interval, in seconds, between RAs that the firewall will send (range is 4-1,800; default is 600). The firewall will send RAs at random intervals between the minimum and maximum values you configure.

Hop Limit

Specify the hop limit to apply to clients for outgoing packets (range is 1-255; default is 64). Enter 0 for no hop limit.

Link MTU

Specify the link maximum transmission unit (MTU) to apply to clients. Select unspecified for no link MTU (range is 1,280-9,192; default is unspecified).

Reachable Time (ms)

Specify the reachable time, in milliseconds, that the client will use to assume a neighbor is reachable after receiving a reachability confirmation message. Select unspecified for no reachable time value (range is 0-3,600,000; default is unspecified).

Retrans Time (ms)

Specify the retransmission timer that determines how long the client will wait, in milliseconds, before retransmitting neighbor solicitation messages. Select unspecified for no retransmission time (range is 0-4,294,967,295; default is unspecified).

Router Lifetime (sec)

Specify how long, in seconds, the client will use the firewall as the default gateway (range is 0-9,000; default is 1,800). Zero specifies that the firewall is not the default gateway. When the lifetime expires, the client removes the firewall entry from its Default Router List and uses another router as the default gateway.

Router Preference

If the network segment has multiple IPv6 routers, the client uses this field to select a preferred router. Select whether the RA advertises the firewall router as having a High, Medium (default), or Low priority relative to other routers on the segment.

Managed Configuration

Select to indicate to the client that addresses are available via DHCPv6.

Other Configuration

Select to indicate to the client that other address information (such as DNS-related settings) is available via DHCPv6.

Consistency Check

Include DNS information in Router Advertisement

Server

Add one or more recursive DNS (RDNS) server addresses for the firewall to send in NDP router advertisements from this IPv6 Aggregated Ethernet interface. RDNS servers send a series of DNS lookup requests to root DNS servers and authoritative DNS servers to ultimately provide an IP address to the DNS client.

You can configure a maximum of eight RDNS Servers that the firewall sends—in the order listed from top to bottom—in an NDP router advertisement to the recipient, which then uses those addresses in the same order. Select a server and Move Up or Move Down to change the order of the servers or Delete a server when you no longer need it.

Lifetime

Enter the maximum number of seconds after the IPv6 DNS client receives the router advertisement that it can use the RDNS Servers to resolve domain names (range is the value of Max Interval (sec) to twice the Max Interval; default is 1,200).

Suffix

Add and configure one or more domain names (suffixes) for the DNS search list (DNSSL). The maximum suffix length is 255 bytes.

A DNS search list is a list of domain suffixes that a DNS client router appends (one at a time) to an unqualified domain name before it enters the name into a DNS query, thereby using a fully qualified domain name in the DNS query. For example, if a DNS client tries to submit a DNS query for the name “quality” without a suffix, the router appends a period and the first DNS suffix from the DNS search list to the name and transmits the DNS query. If the first DNS suffix on the list is “company.com”, the resulting DNS query from the router is for the fully qualified domain name “quality.company.com”.

If the DNS query fails, the router appends the second DNS suffix from the list to the unqualified name and transmits a new DNS query. The router tries DNS suffixes until a DNS lookup is successful (ignores the remaining suffixes) or until the router has tried all of suffixes on the list.

Configure the firewall with the suffixes you want to provide to the DNS client router in a Neighbor Discovery DNSSL option; the DNS client receiving the DNSSL option uses the suffixes in its unqualified DNS queries.

You can configure a maximum of eight domain names (suffixes) for a DNS search list that the firewall sends—in order listed from top to bottom—in an NDP router advertisement to the recipient, which uses them in the same order. Select a suffix and Move Up or Move Down to change the order of the suffixes or Delete a suffix from the list when you no longer need it.