Upgrade Drives on an M-Series Appliance
Table of Contents
9.1 (EoL)
Expand all | Collapse all
-
- Determine Panorama Log Storage Requirements
-
- Setup Prerequisites for the Panorama Virtual Appliance
- Perform Initial Configuration of the Panorama Virtual Appliance
- Set Up The Panorama Virtual Appliance as a Log Collector
- Set Up the Panorama Virtual Appliance with Local Log Collector
- Set up a Panorama Virtual Appliance in Panorama Mode
- Set up a Panorama Virtual Appliance in Management Only Mode
-
- Preserve Existing Logs When Adding Storage on Panorama Virtual Appliance in Legacy Mode
- Add a Virtual Disk to Panorama on an ESXi Server
- Add a Virtual Disk to Panorama on vCloud Air
- Add a Virtual Disk to Panorama on AWS
- Add a Virtual Disk to Panorama on Azure
- Add a Virtual Disk to Panorama on Google Cloud Platform
- Add a Virtual Disk to Panorama on KVM
- Add a Virtual Disk to Panorama on Hyper-V
- Mount the Panorama ESXi Server to an NFS Datastore
-
- Increase CPUs and Memory for Panorama on an ESXi Server
- Increase CPUs and Memory for Panorama on vCloud Air
- Increase CPUs and Memory for Panorama on AWS
- Increase CPUs and Memory for Panorama on Azure
- Increase CPUs and Memory for Panorama on Google Cloud Platform
- Increase CPUs and Memory for Panorama on KVM
- Increase CPUs and Memory for Panorama on Hyper-V
- Complete the Panorama Virtual Appliance Setup
-
- Convert Your Evaluation Panorama to a Production Panorama with Local Log Collector
- Convert Your Evaluation Panorama to a Production Panorama without Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing with Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing without Local Log Collector
- Convert Your Production Panorama to an ELA Panorama
-
- Register Panorama
- Activate a Panorama Support License
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is Internet-connected
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is not Internet-connected
- Activate/Retrieve a Firewall Management License on the M-Series Appliance
- Install the Panorama Device Certificate
-
- Migrate from a Panorama Virtual Appliance to an M-Series Appliance
- Migrate a Panorama Virtual Appliance to a Different Hypervisor
- Migrate from an M-Series Appliance to a Panorama Virtual Appliance
- Migrate from an M-100 Appliance to an M-500 Appliance
- Migrate from an M-100 or M-500 Appliance to an M-200 or M-600 Appliance
-
- Configure an Admin Role Profile
- Configure an Access Domain
-
- Configure a Panorama Administrator Account
- Configure Local or External Authentication for Panorama Administrators
- Configure a Panorama Administrator with Certificate-Based Authentication for the Web Interface
- Configure an Administrator with SSH Key-Based Authentication for the CLI
- Configure RADIUS Authentication for Panorama Administrators
- Configure TACACS+ Authentication for Panorama Administrators
- Configure SAML Authentication for Panorama Administrators
-
- Add a Firewall as a Managed Device
-
- Add a Device Group
- Create a Device Group Hierarchy
- Create Objects for Use in Shared or Device Group Policy
- Revert to Inherited Object Values
- Manage Unused Shared Objects
- Manage Precedence of Inherited Objects
- Move or Clone a Policy Rule or Object to a Different Device Group
- Push a Policy Rule to a Subset of Firewalls
- Manage the Rule Hierarchy
- Manage the Master Key from Panorama
- Redistribute User-ID Information to Managed Firewalls
-
- Plan the Transition to Panorama Management
- Migrate a Firewall to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall to Panorama Management and Push a New Configuration
- Migrate a Firewall HA Pair to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall HA Pair to Panorama Management and Push a New Configuration
- Load a Partial Firewall Configuration into Panorama
- Localize a Panorama Pushed Configuration on a Managed Firewall
-
- Add Standalone WildFire Appliances to Manage with Panorama
- Configure Basic WildFire Appliance Settings on Panorama
- Remove a WildFire Appliance from Panorama Management
-
-
- Configure a Cluster and Add Nodes on Panorama
- Configure General Cluster Settings on Panorama
- Remove a Cluster from Panorama Management
- Configure Appliance-to-Appliance Encryption Using Predefined Certificates Centrally on Panorama
- Configure Appliance-to-Appliance Encryption Using Custom Certificates Centrally on Panorama
- View WildFire Cluster Status Using Panorama
- Upgrade a Cluster Centrally on Panorama with an Internet Connection
- Upgrade a Cluster Centrally on Panorama without an Internet Connection
-
-
- Manage Licenses on Firewalls Using Panorama
-
- Supported Updates
- Schedule a Content Update Using Panorama
- Upgrade Log Collectors When Panorama Is Internet-Connected
- Upgrade Log Collectors When Panorama Is Not Internet-Connected
- Upgrade Firewalls When Panorama Is Internet-Connected
- Upgrade Firewalls When Panorama Is Not Internet-Connected
- Upgrade a ZTP Firewall
- Revert Content Updates from Panorama
-
- Preview, Validate, or Commit Configuration Changes
- Enable Automated Commit Recovery
- Compare Changes in Panorama Configurations
- Manage Locks for Restricting Configuration Changes
- Add Custom Logos to Panorama
- Use the Panorama Task Manager
- Reboot or Shut Down Panorama
- Configure Panorama Password Profiles and Complexity
-
-
- Verify Panorama Port Usage
- Resolve Zero Log Storage for a Collector Group
- Replace a Failed Disk on an M-Series Appliance
- Replace the Virtual Disk on an ESXi Server
- Replace the Virtual Disk on vCloud Air
- Migrate Logs to a New M-Series Appliance in Log Collector Mode
- Migrate Logs to a New M-Series Appliance in Panorama Mode
- Migrate Logs to a New M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Logs to the Same M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Log Collectors after Failure/RMA of Non-HA Panorama
- Regenerate Metadata for M-Series Appliance RAID Pairs
- Troubleshoot Registration or Serial Number Errors
- Troubleshoot Reporting Errors
- Troubleshoot Device Management License Errors
- Troubleshoot Automatically Reverted Firewall Configurations
- Complete Content Update When Panorama HA Peer is Down
- View Task Success or Failure Status
- Restore an Expired Device Certificate
- Downgrade from Panorama 9.1
End-of-Life (EoL)
Upgrade Drives on an M-Series Appliance
- Access the command line interface (CLI) on the
M-Series appliance.Connect to the M-Series appliance in one of two ways:
- Connect a serial cable from your computer to the Console port and connect to the M-Series appliance using terminal emulation software (9600-8-N-1).
- Use terminal emulation software (such as PuTTY) to open a Secure Shell (SSH) session to the IP address of the M-Series appliance.
- When prompted, log in to the appliance.Use the default administrator account and the assigned password.
- Verify that the RAID 1 status for the installed
drives shows there are at least two functioning RAID 1
arrays. During the upgrade, you will upgrade one RAID 1
array at a time and there must be at least one other RAID 1
array that is available to the appliance. The appliance will show
an abort error if you try to remove the only functioning array from
the configuration.Enter the following command to view RAID status:
> show system raid detail
For example, the following shows an output from an M-500 appliance with two available arrays (Disk Pair A and Disk Pair B). If there is only one available array, you must add a second array as described in Add Additional Drives to an M-Series Appliance before you upgrade the drives.Disk Pair A Available Status clean Disk id A1 Present model : ST91000640NS size : 953869 MB status : active sync Disk id A2 Present model : ST91000640NS size : 953869 MB status : active sync Disk Pair B Available Status clean Disk id B1 Present model : ST91000640NS size : 953869 MB status : active sync Disk id B2 Present model : ST91000640NS size : 953869 MB status : active sync
- Remove the first 1TB drive and replace it with a 2TB
drive.
- To remove the first drive from the RAID
1 array configuration (A1 in this example), enter the following
command and enter y when prompted to confirm
the request:
> request system raid remove A1
- Physically remove the first drive from the drive bay. Press the ejector button on the drive carrier in drive bay A1 to release the ejector handle. Then pull the handle toward you and slide the drive out of the appliance.
- Remove a 2TB drive from its packaging and place the drive on a table next to the drive you just removed. Take note of how the drive is installed in the carrier because you will install the 2TB drive in this same carrier.
- Remove the four screws holding the 1TB drive in the carrier and remove the drive from the carrier.
- Attach the 2TB drive to the carrier using the same four screws you removed from the 1TB drive and then reinsert the carrier with the 2TB drive into drive bay A1.
- Enter the following command to verify the 2TB drive
is recognized:
show system raid detail
Verify that the A1 disk shows the correct model and size (about 2TB). If the model and size are not correct, run the above command again until the correct model and size are shown.If the wrong model and size are consistently shown, enter the following command:request system raid remove A1
Wait for 30 seconds once you run the above command, then remove the disk and reinsert it and repeat the show system raid detail command to verify the size and model.
- To remove the first drive from the RAID
1 array configuration (A1 in this example), enter the following
command and enter y when prompted to confirm
the request:
- Copy the data from the remaining installed 1TB drive
in the RAID 1 array to the newly installed 2TB drive in that array.The time required to copy the data may vary from several minutes to a few hours, depending on the amount of data on the drive.
- To copy the data from the 1TB drive in drive
bay A2 to the newly installed 2TB drive in drive bay A1, enter the
following command and enter y when prompted:
> request system raid copy from A2 to A1
- To view the status of the copy process, run the following
command:
> show system raid detail
Continue running this command to view the RAID detail output until you see that the array (A1/A2 in this example) shows Available.At this point, drive A2 will show not in use because there is a drive size mismatch.
- To copy the data from the 1TB drive in drive
bay A2 to the newly installed 2TB drive in drive bay A1, enter the
following command and enter y when prompted:
- Upgrade the second drive in the RAID 1 array
to a 2TB drive.
- Remove the second 1TB drive (from drive
bay A2 in the current example) for the RAID 1 array configuration:
> request system raid remove A2
- Insert the carrier with the newly installed 2TB drive
into drive bay A2 and add it to the RAID 1 array configuration:
> request system raid add A2
The system will copy the data from A2 to A1 to mirror the drives. - To view the status of the copy process, run the following
command:
> show system raid detail
Continue to view the RAID detail output until you see that the array (A1/A2 in this example) shows Available and both disks show active sync.Disk Pair A Available Status clean Disk id A1 Present model : ST2000NX0253 size : 1907138 MB status : active sync Disk id A2 Present model : ST2000NX0253 size : 1907138 MB status : active sync
- Remove the second 1TB drive (from drive
bay A2 in the current example) for the RAID 1 array configuration:
- Upgrade drives for additional RAID 1 arrays
as needed.To upgrade additional RAID 1 arrays to 2TB drives, repeat this procedure replacing the drive designators as applicable. For example, replace A1 with B1 and A2 with B2 to upgrade the drives in the B1/B2 RAID 1 array.