NAT Policy Overview
Focus
Focus

NAT Policy Overview

Table of Contents

NAT Policy Overview

You configure a NAT rule to match a packet’s source zone and destination zone, at a minimum. In addition to zones, you can configure matching criteria based on the packet’s destination interface, source and destination address, and service. You can configure multiple NAT rules. The firewall evaluates the rules in order from the top down. Once a packet matches the criteria of a single NAT rule, the packet is not subjected to additional NAT rules. Therefore, your list of NAT rules should be in order from most specific to least specific so that packets are subjected to the most specific rule you created for them.
It is important to understand that in firewall policy rules (including NAT), the set of IPv4 addresses is treated as a subset of the set of IPv6 addresses. However, the set of IPv6 addresses is not a subset of the set of IPv4 addresses. An IPv4 address can match a set or range of IPv6 addresses; but an IPv6 address cannot match a set or range of IPv4 addresses.
In all policy types, the keyword any for a source or destination address means any IPv4 or IPv6 address. The keyword any is equivalent to ::/0. If you want to express "any IPv4 address", specify 0.0.0.0/0.
During policy matching, the firewall converts an IPv4 address into an IPv6 prefix where the first 96 bits are 0. An address of ::/8 means, match the rule if the first 8 bits are 0. All IPv4 addresses will match ::/8, ::/9, ::/10, ::/11, ... ::/16, ... ::/32, ... through ::/96.
If you want to express "any IPv6 address, but no IPv4 addresses", you must configure two rules. The first rule denies 0.0.0.0/0 to deny any IPv4 address (as the source or destination address), and the second rule has ::/0 to mean any IPv6 address (as the source or destination address), to satisfy your requirement.
Static NAT rules do not have precedence over other forms of NAT. Therefore, for static NAT to work, the static NAT rules must be above all other NAT rules in the list on the firewall.
NAT rules provide address translation, and are different from security policy rules, which allow or deny packets. It is important to understand the firewall’s flow logic when it applies NAT rules and security policy rules so that you can determine what rules you need, based on the zones you have defined. You must configure security policy rules to allow the NAT traffic.
Upon ingress, the firewall inspects the packet and does a route lookup to determine the egress interface and zone. Then the firewall determines if the packet matches one of the NAT rules that have been defined, based on source and/or destination zone. It then evaluates and applies any security policies that match the packet based on the original (pre-NAT) source and destination addresses, but the post-NAT zones. Finally, upon egress, for a matching NAT rule, the firewall translates the source and/or destination address and port numbers.
Keep in mind that the translation of the IP address and port do not occur until the packet leaves the firewall. The NAT rules and security policies apply to the original IP address (the pre-NAT address). A NAT rule is configured based on the zone associated with a pre-NAT IP address.
Security policies differ from NAT rules because security policies examine post-NAT zones to determine whether the packet is allowed or not. Because the very nature of NAT is to modify source or destination IP addresses, which can result in modifying the packet’s outgoing interface and zone, security policies are enforced on the post-NAT zone.
A SIP call sometimes experiences one-way audio when going through the firewall because the call manager sends a SIP message on behalf of the phone to set up the connection. When the message from the call manager reaches the firewall, the SIP ALG must put the IP address of the phone through NAT. If the call manager and the phones are not in the same security zone, the NAT lookup of the IP address of the phone is done using the call manager zone. The NAT policy should take this into consideration.
No-NAT rules are configured to allow exclusion of IP addresses defined within the range of NAT rules defined later in the NAT policy. To define a no-NAT policy, specify all of the match criteria and select No Source Translation in the source translation column.
You can verify the NAT rules processed by selecting DeviceTroubleshooting and testing the traffic matches for the NAT rule. For example: