PA-54R-POE-D-5G
Table of Contents
PA-54R-POE-D-5G
View the interfaces, power inputs, and other components located on the front and back
panels of the PA-54R-POE-D-5G firewall.
The following image shows the front panel of the PA-54R-POE-D-5G. The table lists and
describes each labeled component.
| Item | Component | Description |
|---|---|---|
|
1
|
Management Port
|
One RJ-45 10 Mbps/100 Mbps/1000 Mbps port that is used to access the
management web interface and perform administrative tasks. The
firewall also uses this port for management services, such as
retrieving licenses and updating threat and application
signatures.
|
|
2
|
Fiber SFP Ports
|
Two SFP ports for 100Mbps/1000Mbps network traffic.
|
|
3
|
Console Port (RJ-45)
|
One RJ-45 port used to connect a management computer to the firewall
using a RJ-45 to USB cable and terminal emulation software.
The console connection provides access to firewall boot messages, the
Maintenance Recovery Tool (MRT), and the command line interface
(CLI).
Use the following settings to configure your terminal emulation
software to connect to the console port:
|
|
4
|
Console Port (USB-C)
|
One USB-C port used to connect a management computer to the firewall
using a standard USB-C cable.
The console connection provides access to firewall boot messages, the
Maintenance Recovery Tool (MRT), and the command line interface
(CLI).
Use the following settings to configure your terminal emulation
software to connect to the console port:
|
|
5
|
Ground Studs
|
Dual screw ground lugs used to connect the firewall to earth
ground.
|
|
6
|
Copper RJ-45 Ports
|
Twelve RJ-45 ports for 10 Mbps/100 Mbps/1000 Mbps network traffic.
You can set the link speed and duplex mode or choose
autonegotiate.
Ports 9, 10, 11, and 12 are Power over Ethernet (PoE) ports that can
each transfer up to 90W of power to a connected device. The maximum
PoE budget is 90W. Refer to the electrical
specifications for more PoE information.
You must use Shielded RJ-45
Ethernet cables in order to meet compliance requirements. |
|
7
|
USB-C Port
|
One USB-C port used for debugging and administration only. Use it to
bootstrap the firewall or perform self-service enhanced factory
reset (EFR).
Bootstrapping enables you to provision the firewall with a specific
PAN-OS configuration and then license it and make it operational on
your network.
EFR provides remediation of a compromised or potentially compromised
firewall to initiate a complete cleanup of the device.
|
|
8
|
GNSS Ports
|
Two Global Navigation Satellite System (GNSS) ports that can be used
for active GPS/GNSS antenna support if required.
|
|
9
|
Digital I/O
|
An accessible digital I/O with eight LEDs used for interfacing with
external sensors, relays, or controllers.
|
|
10
|
BATT- and IGN+ Input
|
A connector used to enable Vehicle Ignition Monitoring System
(VIMS) when you connect a cable between this input and a
vehicle's ignition circuitry.
This port is only active when it detects an
AMPSU (Automotive Power Supply Unit). |
|
11
|
Antenna Connectors
|
Four SMA-F connectors used to install 4x4 MIMO antennas that provide
5G connectivity to the device.
|
|
12
|
Power Inputs
|
Two DC power inputs used to connect power to the firewall. A second
power input can be used for redundancy.
|
|
13
|
SIM Access Cover
|
Once the cover is removed, there are two slots in which you can
install 4FF nano SIM cards to enable mobile network
connectivity.
It is recommended that the 4FF
nano SIMs you use are within industrial temperature range. The SIM access cover must
remain on while the firewall is in operation. |
|
14
|
LED Status Indicators
|
Ten LEDs that indicate the status of the firewall hardware
components. Refer to the LED definitions to view the
color and behavior of each LED.
|
The following image shows the back panel of the PA-54R-POE-D-5G. The table lists and
describes each labeled component.
| Item | Component | Description |
|---|---|---|
|
1
|
DIN rail mounting clip
|
Use this mounting clip to Install the PA-50R Series Firewall on a DIN Rail.
|
|
2
|
LED Status Indicators
|
Eleven LEDs that indicate the status of the firewall hardware
components. Refer to the LED definitions to view the
color and behavior of each LED.
|