config interface
Table of Contents
config interface
Use the
config interface
command
to configure a physical or a logical interface and consists of sub-commands—create
a point to point protocol over ethernet (PPPoE) interface on a parent
physical interface, update PPPoE interface details, configure the
LLDP state of a selected interface, configure or enable the PoE
threshold of a selected interface.PPPoE option is only
available for preclaimed or unclaimed devices.
Command
config interface interface-number (pppoe | ip | ip6 | mode | mtu | usedfor= (none | private | public | private-l2) | enabled = (false | true))
config interface (cellular1 | cellular2) (apn (auto-apn | name) | iptype (ipv4 | ipv6 | ipv4v6)| mtu | enabled= (false | true))
config interface interface-number ipv6 (autoconf | static address= | pppoe | none)
config interface <id> lldp state=(rxonly or txrx)
config interface <id> poe enabled=true-usage-threshold 60
Options
pppoe | description | Enter a description for the PPPoE interface. |
pppoeuser | Enter the challenge handshake authentication
protocol (CHAP) or password authentication protocol (PAP) user name
for PPPoE authentication. | |
pppoepasswd | Enter the CHAP or PAP password for PPPoE authentication. | |
servicename | Enter the name of the PPPoE service provider
for connection. A WAN network has multiple service providers and
select the service name field. | |
adddress | Enter the IP address of the remote shim. | |
gw | Enter the IP address of the Gateway. | |
reconnectdelay | Enter a value for delay (in seconds) for PPPoE
reconnection. | |
hostuniq | Enter an even-sized hexadecimal number to set
a value for Host-Uniq. | |
ip | static | gw - Enter the IP address for the gateway. |
dns - Enter the DNS address. | ||
address - Enter the static IP address of the
interface. | ||
dhcp | hostname - Enter a single hostname or comma
separated multiple hostnames. | |
clientid - Enter the DHCP client identity. | ||
pppoe | Select pppoe to configure a PPPoE interface. | |
none | Enter none to reset previously entered information. | |
ipv6 | static | gw - Enter the IP address for the gateway. |
dns - Enter the DNS address. | ||
address - Enter the static IP address of the
interface. | ||
autoconf | Indicates the Global IP address is derived using stateless
address autoconfiguration (SLAAC). Release 6.2.1 | |
pppoe | Select pppoe to configure a PPPoE interface.
Release 6.2.1 | |
none | Enter none to reset previously entered information.
Release 6.2.1 | |
mode | auto | Select auto for automatic negotiation. |
speed | Select speed as 10, 100 or 1000 MBPS. | |
duplex | Select duplex for duplex negotiation. | |
mtu | Enter a number between 552-1500.
The default value is 1500. | |
usedfor | none | Enter none when interface is used as a controller
port (just for connecting to controller). |
private | Enter private to configure the interface for
a private WAN. | |
public | Enter public to configure the interface for
a public network. | |
private-l2 | Enter private-l2 to configure an L2 interface
as part of a bypass pair. | |
enabled | true | Enter true to enable the interface. |
false | Enter false to disable the interface. | |
Cellular Interfaces | ||
apn | auto-apn | When you select auto-apn, default carrier APN
is automatically detected and the device connects using auto-APN profile. |
name= | Enter the name of the APN profile. Optional
parameters are auth-type (pap, chap, pap/chap), username, and password. | |
iptype | ipv4/ipv6/ipv4v6 | Configure cellular iptype options IPv4 / IPv4v6 on the cellular interface. In
case of IPv4v6, devices can run IPv4 and IPv6 in
parallel. Release 6.1.1 |
mtu | MTU number must be between 552-1428
for IPv4 and 1280-1428 for IPv6. The default value is 1428. | |
enabled= | false | Enter false to disable the cellular interface. |
true | Enter true to enable the cellular interface. | |
lldp state | All non-PoE ports are set to receive-only
mode and PoE ports are set to transmit and receive mode. | |
rxonly | LLDP packets in receive only mode. | |
txrx | LLDP packets in transmit and receive mode. | |
poe | Configure PoE ports. | |
enabled= | Enter true to enable or false to disable the
PoE port. | |
usage threshold | Enter a usage threshold percentage. | |
Command Notes
Role | Super |
Related Commands |
|
Introduced in | Release 4.5.1 |
Example
config interface controller1 ip dhcp config interface 3 pppoe pppoeuser=root pppoepasswd=pass config interface config interface 2 ip static address=10.10.10.252
config interface cellular1 apn name=test auth-type=pap username=test1 password=test2
config interface cellular1 iptype version=ipv4
config interface cellular1 iptype version=ipv6
config interface cellular1 iptype version=ipv4v6
config interface 5 ipv6 static address=2001:10:3:5::100/64 gw=2001:10:3:5::1 dns=2001:4860:4860::8888
